Search results for query: *

  1. JoesEdge

    Installing an American Autowire Classic update wiring harness

    I just recently purchased this kit and read in the instructions that I can't use my 3 wire Toyota alternator that charges superbly at idle, even thought it's probably only 60 amps or so. In the instructions say to use a 1 wire self-regulated alternator. Anyone have a a recommendation on a good...
  2. JoesEdge

    Clutch Master Cylinder Mounting

    @68 A Have any more of these?
  3. JoesEdge

    Diff Housing Narrowing In SoCal

    @clin10 Here's another one for you. They are in Huntington Beach, CA. J & S Gear Co – We Build The Best Gears. I haven't used them personally, but when I do rebuild my 8 3/4 and add a Sure-Grip or something I plan on taking it to them. I have read good things about them.
  4. JoesEdge

    Diff Housing Narrowing In SoCal

    I live in Downey, so Cooks isn't too far from me. I had them reweld the spring perches on my 8 3/4 rear end a few years back. Quick and affordable.
  5. JoesEdge

    Pro Flo 4 Timing

    Are you running a Magnum serpentine setup? Just curious.
  6. JoesEdge

    Junkyard Magnum Motor Finds

    Awww... that's terrible news! And they really nickel and dime you at LKQs too. Core charge, on a used part? Seriously??? :(
  7. JoesEdge

    Junkyard Magnum Motor Finds

    I miss the days of the 40% discount at LKQ. I haven't seen that since pre-COVID. The LKQ in Ontario usually has a good inventory of old Mopars. I pulled a 440 out of a motorhome there. I pulled a 400 out of a land yacht in the Wilmington LKQ.
  8. JoesEdge

    Junkyard Magnum Motor Finds

    @pishta Is the warranty mandatory now, or you threw that in just in case the block is bad?
  9. JoesEdge

    Junkyard Magnum Motor Finds

    If you settle for a 5.2 Magnum. I have one I could sell you. Otherwise, LKQ is your best bet for a 5.9 Magnum. You can easily locate one because the LKQ yards are full of old Dodge RAM 1500, 2500, and 3500's. They even post the VIN number so you can use a decoder to see what engine it had.
  10. JoesEdge

    Tremec

    For the 6 speed swap. I updated my post to mention that. I agree it was confusing. I figured if I am going to cut the torsion bar support, I might as well go 6 speed. I know it's more expensive than a TKX. I'm not sure how much of a savings there would be with a TKX. By the way, I have a...
  11. JoesEdge

    Tremec

    That is really nice metal work! I wish I had that kind of talent!
  12. JoesEdge

    Tremec

    Interesting! So, instead of brace going OVER the transmission (like the factory did) the Holley torsion bar cross member braces from underneath. I just don't like that it is bolt in, but I guess that aids in getting the transmission in and out of position. I was just quoted about $7,000.00...
  13. JoesEdge

    Pro Flo 4 Timing

    Brian built my motor too. It's been running good for the pat 6 years. I do plan to give it a refresh though before I go EFI. Just to make sure it's still healthy. @BergmanAutoCraft did you see on the Edelbrock forums how Edelbrock shutdown the threads regarding the distributor phasing...
  14. JoesEdge

    Tremec

    I've been considering this swap and just getting everything from Silver Sport Transmissions. Just not sure if they still use the ToddRon crossmember brace or if they built something different. The only thing that makes me hesitate is that I'm not good with sheet metal fabrication.
  15. JoesEdge

    Kicking around the idea of a Roller Cam Swap...

    Yeah, I called IMM Engines the other day and talked to Fred and he confirmed that it's tough finding hydraulic roller cams.
  16. JoesEdge

    Kicking around the idea of a Roller Cam Swap...

    Well, interesting that you mentioned that. I do have a Magnum block sitting in the garage. That would be roller done right since it came from the factory that way.
  17. JoesEdge

    Kicking around the idea of a Roller Cam Swap...

    Hey all! I hope everyone had a great Thanksgiving. I was recently kicking around the idea of swapping out my flat tapper hydraulic cam for a hydraulic roller cam. Currently, I have the the Comp Cams XE268H cam in my LA 360 with 9.6:1 compression, Magnum EQ heads with 1.6:1 Comp Cams roller...
  18. JoesEdge

    K-FRAME STITCH WELDING......THOUGHTS?

    Weld it up! I welded and powder coated mine. I tried to find the best pics I could. Yes, do weld up the steering box mount. That area flexes quite a bit.
  19. JoesEdge

    Magnum dyno videos

    Who built this engine? IMM Eninges? The power was similar to my engine built by IMM Engines. Mine is an LA block with EQ Magnum heads though and a XE268H cam.
  20. JoesEdge

    Serpentine set up question

    In case anyone needs it, I have a spare No-A/C Magnum Alternator bracket. You can go here for more info: [FOR SALE] - Magnum Alternator Bracket (No A/C) with Bolts
  21. JoesEdge

    [FOR SALE] Magnum Alternator Bracket (No A/C) with Bolts

    Hey Mopar people!! I have an extra Magnum Non-A/C Alternator Bracket. These are almost impossible to find. It's great for you guys that are swapping in Magnums into your A-Body or want to use the Magnum serpentine belt system and DO NOT have Air Conditioning. PRICE: $65.00 shipped via USPS...
  22. JoesEdge

    Pro Flo 4 Timing

    Seems like Edelbrock has spoken. The title of their post isn't specific on either Big Block or Smallblock, but the pictures are definitely a Big Block. Check out what they have to say: ProFlo Mopar Distributor Rotor Phasing - Edelbrock Community Forum
  23. JoesEdge

    Pro Flo 4 Timing

    I blame the crappy service because Edelbrock is pulling their headquarters out of California (probably doesn't make a difference, but I'm bitter). Some of the foundries are still here in California though, like 2 hours south of me. It used to be nice when they were down the street. Actually...
  24. JoesEdge

    Pro Flo 4 Timing

    @GMachineDartGT I'm assuming the fuel hoses come up along the firewall? Do you have any pictures of how you ran those? No worries with the heat from the headers? What type of hoses are you running? Thanks!!!
  25. JoesEdge

    Pro Flo 4 Timing

    By any chance, did you post this to the Edelbrock forums too? Doing so may light a fire under their butt to fix it or offer the part as well as a work around solution.
  26. JoesEdge

    1974 Duster Headliner

    Same gasket as the windshield. The headliner tucks inside the lip of the windshield gasket. The other thing that holds it up are the visors and rear view mirror.
  27. JoesEdge

    What's the electrical pin type for MSD Distributor connection?

    Wow! Thanks! You must have searched for these before or something. I'm gonna look them up. I've shopped around on Mouser and Digi-Key before for Arduino projects, so I'm familiar with those sites. Thanks again!
  28. JoesEdge

    What's the electrical pin type for MSD Distributor connection?

    Hey Mopar gang! Do any of you electrical wizards know what type of electrical pins MSD uses for their 2 pin distributor connector and where I could find them? I'd like to make a couple harnesses using the casings I already have, but I just need the pins and wanted to buy a bunch sets to have a...
  29. JoesEdge

    Van power steering bracket issues

    Sold it, but I'm always looking out for them in the wrecking yard.
Back
Top