Search results for query: *

And the answer is 3.23

And the answer is 3.23

Thank you demon

I have a 8.25 posi rear end out of a 84 diplomat, and I am getting ready to put it in , all literature said it is a 3.55 gear, some friends said it is 3.23 gear...how do I count the gear to figure this out Thanks

I only get to look at this email once in a while...my phone email is not allowed

thanks.. trying to put a 8.1/4 pos on my 66 dart, rebuilt and brackets moved just need the brake setup and c clamps

Need rear backing plates for a 1984 diplomat 8.1/4

I have Been looking for backing plates for a 84 diplomat, will your plates fit..

to answer your question I have a Edlebrock 4 barrel and the bar being to short is the one with the slider from the kickdown. sorry typing too fast

the cable I was referring to was for the throttle the travel was to short, but I have fixed that for now. My big concern is the kickdown, I now the bar is too short right now, I will be looking for a better set up at the swap meet in Waukesha wi this weekend. the question I don't know is the one...

I am finishing the install of a 318 with a 904 tranny. Number one is that the cable I went to is too long and had to modify so that my 4 barrels would open . I need to find the right one . #2 is that I have a single bar kick down for the 904 , but something doesn't seem right , maybe the travel...

how are the floor boards, will they fit in a 1966 dart, and if so $

have tried several (original) mounts always too short .i'm just going buy what people sold me saying this is the one . anyway there is a guy i know that will cut me the bushings for stearing out of nylon since i posted this . will send pictures just working on pedal and i will start it

thanks alot that is some of the info i needed, Dan

save your self the headache . i just went through this . I was told the 318 and the 273 are the same block the thin ones did not fit on the k frame of the 63 to 66. the thick ones didn't either . I have both if you would like to try them. buy the schumacher mounts for your make and engine size...

I know it sounds stupid but it has been again 40 years since working on a car like this . i have a electical block on the firewall i think i still need were the bat and the starter connect to i have a resistor .i have a electronic choke on the new carb with no wire to run it to . i would figure...

I have a gm hei distributor i'm told , and needs only one 12 volt wire to it

menomonee falls ...by milwaukee

finishing up the rebuild from a slant 6 to 318 and ran into snags. 1. wiring from a points distributor to one wire electric distributor.???? 2. new wiring harness under hood to plug into old firewall....what is it called and where do i get it. 3. anyone willing to help in wisconsin, I'm...

I have the kick down. need what ever pedal linkage will work ,

If I have to go to cable I will , yes i had a slant 6, dropped in a 318 finishing up and that is one of the parts i needed. Thought that there was linkage for the v8's

I am looking for the gas pedal linkage to a 1963-66 dartgt with a v8 small block 4barrel

yes that looks like the parts

In my field of hvac you need a compressor that is high volume and quiet. oil-less good to fill a tire, but have ear plugges. through it all away and buy a Quincy compressor , it will last a lifetime . just change the oil yearly on any compressor

need alternator bracket (looks like a triangle shape and adjustment bar for 318

I just swapped out my 67 k 225 for a rebuilt 318 , these guys walked me through a lot i still am working on alt brackets and such but word of warning had hard time with headers on 1963 to 1966 the stearing box is in the way . have some new headers in box still sitting in garage. ended up for now...

sorry been busy, update on 1966 dodge dart gt , 318 is in after a fight with mounts and brackets . guys do the right thing and just buy the schumacker mounts. number two a 904 rebuilt transmission mounted on a 318 fits perfect in the dart. changed the brakes from single master to dual master...

i WANTED TO THANKS GRUMPUSCREATURE AND I DIDN'T OR COULDN'T FIND WERE TO THANK HIM SO I WILL LOOK LIKE A DORK BUT I DON'T CARE. HE HAS HELPED ME OUT GREATELY AND FOR THAT I WOULD LIKE TO HELP SOMEBODY ELSE OUT IN THE FUTURE. I HAVE SOME PARTS THAT I WILL GIVE UP FOR FREE TO FABO MEMBERS .AND I...

As some of you know I am Building a 1966 Dart Gt. Unfortunately I am having a learning curve that has cost me a few times . anyway thank you all of your help. so now to the message . I ordered headers for a 318 in a 1966 dodge dart gt. from DNA Motoring in july , looked at them but did not fit...

OK thanks. I'll start looking