Search results for query: *

Does anyone know what was the correct length for the accelerator cable for the Hemi Cross Ram

Can some tell me what this trans is from PK4431557 9163 2731. Thank you

Looking for ideas on how to connect a Edelbrock RPM air gap manifold with a Holley 4160 to the throttle cable and kickdown lever. Trying to use factory linkage, but we are open to ideas of aftermarket. Thanks

I am looking for a 904 transmission output shaft support it has a number cast into it of 2466881 , and it supposedly fits 66 to 86. Thanks in advance Bob

I am in need of a right hand upper control arm for a small ball joint a body. TIA

Looking for a manual brake master cylinder push rod and pedal nut and bolt. Thanks

Looking for a nice set of shock plates for a 8 1/4 or 8 3/4 rear axle for an A body. TIA

I am in need of a section of the over the rear axle floor pan. It is the section in the panel just forward of the trunk pan between the rear frame rails and forward to the rear upper shock mounts. 340-duster at sbcglobal dot net or PM me here on this board Thanks

How many owners of 70-72 Dusters and 71 72 Demons with the metal upper door frame, have seen buckling or cracks in the door inner at the cat whisker about the middle of the door ? If so what have you done about it?

After 3 different pivot shafts not having a solid press fit to my lower control arm bushing, I have to suspect the bushing to be bad. Can anyone tell me the correct diameter for an A body lower control arm pivot shaft. TIA

What are the differences in a 4235 and a 4236 carburetor , in other words what makes one a left hand carb and the other a right hand carb?

I am looking for a driver side grille surround for parts, as the vendor who reanodized my surrounds lost one of brackets and I am trying to get them detailed now to reassemble. Thanks

Looking for pictures of the orange paint markings that is supposedly found on the lower steering column jacket , and on the K-frame, signifying they were for a Hemi A body. Does anyone have any additional info on this?

I have a Aug. 1968 318 for sale. This engine is complete, minus water pump, and alternator brackets, it includes the carb, distributor, engine mounts, throttle bracket and return spring bracket, moroso valve covers, 90 degree oil filter adapter, and dual groove crank pulley, air cleaner. The...

Looking to verify what master cylinder and what distribution tee was used on the original cars. Do they have a two piece rear brake line with a second block inline of the rear pipe, or were they one piece with only the front distribution tee?

Would it be a good idea to install offset upper control arm bushings to make up some of the lost length in the control arm , when the K frame spacers are installed? Has anyone tried that and if so , what positioning worked the best? Thanks

I am looking for a least one clean pre 72 strut rod, I will take a pair. They must be free of any nicks/gouges, not bent and have good threads. Thanks Bob

i am looking for pictures of the steering column under dash specifically of the ground wire that is secured to the column bracket.

I am currently building my own 68 super stock clone Barracuda, and I am in the process of mounting my brackets to the K frame for the engine. I am using factory style reproduction mounts, on a clean v8 k frame, with TTI headers. I have followed their instructions, and would like to know if...

I have a Aug. 1968 318 for sale. This engine is complete, minus water pump, and alternator brackets, it includes the carb, distributor, engine mounts, throttle bracket and return spring bracket, moroso valve covers, 90 degree oil filter adapter, and dual groove crank pulley. I also have 318...

I have some transmissions to sell. First is a 1964 Cable shift. flanged tail shaft, big block ,console shift 727, part number E2464734, the trans is disassembled but is complete with all parts included $100 Second another 1964 cable shift 727 for a small block part number E2464423 , this...

I have a 7 1/4" axle for sale it has 10" brakes . Wheel cylinders and brakes lines were replaced recently before it was removed from my 1968 Barracuda. Axle spins freely and appears to be in great shape. Also included is the correct pinion snubber. Will not ship $75.00 Located in Armada Mich.

I have a complete June of 1970 360 engine .It is stamped with a 71 VIN. It was a running engine when it was removed , about 10 years ago. It is complete except the distributor, and exhaust manifolds. I will be selling it with engine mounts, alternator and brackets, power steering pump,brackets...

I am in the process of replacing the quarters on my 68 fastback and in trying to get as much gap to the decklid I would like to know what others are measuring for a gap to the decklid, Specifically near the most rearward corner of the quarter panel just in front of the taillight .Then also what...