Search results for query: *

Wow I have to admit I thought I would have had a little interest in this Duster H mm..

1970 Duster original 318 904 8 ¾ Power Drums car. Now has a magnum block 360 out of 1996 ram 25K miles when pulled less than 20 miles since I put it in the duster Factory serpentine belt setup Electronic ignition Aluminum intake Carter comp 4 barrel Headers with new 2 ½ duals Flows X-pipe...

Check this thread http://www.forabodiesonly.com/mopar/showthread.php?t=14612 I just did this myself and you are right it is hard to see whats going on. The trick is you wont see it is all feel, You must have the right tool. I think in the thread there is a picture of one. I found it easier to...

According to my haynes book '94-'98 318's had 0.432' lift intake / exhaust and 360's had 0.410" lift intake / exhaust....... I must admit my '96 360 with carb runs really good but I am looking for a replacement cam for the motor to step it up a little...

I have a tool that is similar to the one that is pictured. I have managed to get the rear window trim off. I also have the top half of the front and it started fighting me so I stopped, will try again today. Don't want to damage it.....

To bad you are not closer as I can likely save all of your pic and doc's etc. My trick is to use a live Linux cd which boots and runs off the cdrom only and then you can access the windows hard drive and save to a usb thumb drive. I have had good success doing this. Mepis Linux or PCLinuxOS...

It sounds like this web page is being loaded from the cache file. Try deleting the cache and or cookies. You should be able to do this through your internet settings or preferences.

I am getting ready to pull the rest of the glass from my '70 Duster and I need to remove the trim from the front and rear glass. What's the best way to do this? It is in great shape and I do not want to bend it..... I know it has clips but I am concerned about using to much force.... Any help...

I just did 2 1/2 inch duals with a X pipe and the force mufflers from jegs all the way out the back on my 1970 Duster and it sounds great. Seem to be made really well too. Sound just like flowmasters to me, The guy at the muffler shop thought they were FM's I highly recommend them.

I saw them on '69 Valiant's 1250.00 Is a little pricey for me though I will continue to look for a used one that is in good shape

I knew I have seen one here also. Now I am on a quest to find one for My 1970 duster.... It looks like it should bolt right in. They look great

The more I look at I really like it too. I am preping my Duster for paint ATM and my grill has a few broken places. I am considering this as a replacement Does anyone have one of these for sale??

I just saw this car on ebay and thought the grill looked different. It kinda caught me off gaurd. I do like the look. I know someone knows what model / year this grill came from. Does anybody know if it is direct bolt in replacement option?

Just trying to finish body work and get it ready for paint. I would just like to strip of the moulding chrome etc. My buddy who has been helping me wants to pull everything-all glass all trim from doors gut the inside, I am sure some of you know the routine. He is used to this type of resto...

That is one wild ride WOW!!!!

I kind of have the same question except reversed. I just pulled the A/C - Heater box out of my '71 Duster and do not want to put it back. I just want a heater only. I do not have A/C anymore. Are they physically the same minus the A/C section ? Heat isn't a really big deal in Tucson but I at...

That is one super nice Duster. Great job!!!!!!!!!

For this car it probably doesn't matter if it is aftermarket or not. Just something that looks good on the car. I will see if I can find their website or catalog Thanks

Thanks for the kind words everyone. It is a great start. It is hard to tell in the pictures with all of the dirt and greasy hand prints, but this car is really straight and very minor rust. We are getting ready to start blocking it down and get it ready for color now that is not so hot outside...

A little history on this Duster. I traded a waterbed for it about 8 years ago, what bargin. It had a 318/904 it ran and drove but had a screamming squeal (spun mains) It now has a 360 magnum right out of a 95 ish ram (it was sitting on a frame out behind a trailer house just north of here it...

Just got back from the exhast shop and since it was out of the carport I thought I would take a couple of pic's and share with everyone. Still a work in progress but it is comming along

I got the Duster back from the muffler shop today. I must say I am very pleased with the work they did and it sounds great. The X pipe, the generic flowmasters, 2 1/2 pipe all the way. It is much quieter than I expected and seems to have more power than the 2" system that this replaced. It did...

Right at the moment it has a 360 Magnum right out of a stock 95 truck 20k miles. All that I have done is change to carb via mopar dual plane manifold and a electronic dist headers elde carb. I even kept the serpetine belt setup. Down the road I will do some mild motor work or maybe start from...

I just wanted to hear what others are or have paid for a set of dual exhaust for their A-body. I am plannining on going to the exhaust shop tomorrow so they can run 2.5 inch pipe from the headers with a X pipe all the way out the back. Muffler of choice/price is Jegs Force generic style...

Can I relate to this WOW! I just pulled my headers for a blown gasket and missing bolt , it was on a duster with power steering. It turned into a 2 weekend job including finding all the parts I replaced since it had to unbolt both motor mounts. jack the motor until it hit the firewall The right...

I must confess I used to do body and paint when I was younger. For this I did ask for assistance from a close freind of mine who kinda runs and does most if not all the sheetmetal and fabrication and everything else etc.... at Hot Rods and Classics of Tucson. A very smart move on my part I must...

Just finished the driver side rear 1/4 panel today of my 1971 Duster. It took the better part of the afternoon. The bottom 4 inches or so had some rust that was covered by some bondo and bubbling up. I just thought I would post a few pic's. The inner panel had a small area that we cut out and...

I got the package today Thanks a MILLION

I am glad it work for you too. I do not know any Mopar people here in Tucson. I guess I need to get out more