Search results for query: *

I found a video of someone using one of these to drill out and install bronze valve guides on the youtube. It appears to have been long discontinued and very hard to find. Anyone use or have one of these things?

Anyone know where i can get one of these rebuilt? the nicer of the two is in pretty good shape , but the upper bushing is a little worn. for some reason they are both painted a different color of orange .

i’m trying to figure out where to buy the correct piston pin c clip retainers for my stock style late 80’s Sealed power 2369p pistons with floating pin. One of my clips is bent so i’d like at least one but would prefer to replace all of them. I’ve searched online and this forum and the ones i’ve...

I need some advice on where to buy the correct alternator for my non a/c 340 swinger. The original alternator is long gone. I have a stock wiring harness and a new old stock 69 voltage regulator. It seems like most of the aftermarket and rebuilt alternators available are much higher amp rating...

So i just measured my crankshaft main and rod journals to check for wear and taper .I’m doing a light rebuild with new bearings and rings and seals. I had this crank machined decades ago when i was in high school by a machine shop that is no longer in business. the rods are .030 under and the...

I’m trying to identify these aftermarket 340 pistons from a 30 year old build. the casting number is 1029p . I had the short block rebuilt when i was in high school. I don’t remember specs . I remember the guy taking me into lowering compression ratio to run pump gas. Probably because i was a...

I just saw this listing. I can’t believe this car still exists. Guy wants a pretty penny for it 1969 Dodge Dart | eBay

I found resale shop online that specializes in nos car parts that has this 40 year old sealed power replacement 340 cam . I looked up part numbers and verified that it’s the correct cam. the only thing i’m concerned about is condition. I looks like there might be a small amount of rust on the...

Hear is a question i haven’t seen asked. I’m putting back together my mostly stock 340 engine out of my 69 swinger 4 speed . back in the 90s it had the mopar 292/508 cam with the recommended mopar red valve springs installed. i cannot recall the part number. I am planning on putting the stock 69...

i’m looking for a set of spring hangers with 5/8 bolt for 340 dart. preferably ones that aren’t too rusty. mother nature ate mine up. thanks

Anyone used Tamco paint? They say the can mix up in factory colors in single stage urethane or base coat clear. I see a bunch of youtubers using it with great success. It much more affordable than PPG .

This is an Auto Metal Direct 1967 1968 1969 Dodge Dart weatherstrip gutter channel lower left and right. You get what you see in the pictures. They are in new condition. They are located in Montgomery,IL 60538 $75 + shipping I accept PayPal or Cash at local pick up. Thanks

This is a AMD left rear spring perch for 1966 thru 1976 mopar a bodies. This fits the drivers side. $44 + shipping Montgomery,IL 60538 I accept PayPal for payment or cash at local pick up thanks

Anyone know why these 340 callouts only fit upside down? I bought them on eBay years ago. The hood is original to the car. I'm pretty sure the original ones didn't fit like this.

anyone have pictures of what the grill brackets that attach the 2 center posts of the 69 dart grill to the radiator support?

This is a left front drivers side fender for a 1968 Dart . It has some rust through on the lower dog leg area. The rest of the fender is rock solid. Price is $75 pick up only in Montgomery, IL 60538.

does anybody know if the 1969 340 cars came with a 14x5.5 spare or did they use the standard 14x4.5 rim? Thanks!

This is a 1972 Dodge Plymouth Chrysler mopar LA 318 small block . It was in a manual transmission car and has a pilot bushing in crank. This Engine needs a rebuild /overhaul . It has been sitting a long time. The engine turns over by hand. One of the heads has been off to check cylinder bore...

This is a left front drivers side fender for a 1968 Dart . It has some rust through on the lower dog leg area. The rest of the fender is rock solid. I believe this will fit on 1967 also with a few modifications. Price is $100 pick up only in Montgomery, IL 60538.

This is a 1972 318. The engine turns free . I had one of the heads off and it appears to be standard bore. The guy I bought it from said it ran before he took it out of the challenger project he was working on. It will need a complete overhaul. It comes with the engine stand. Local pick up only...

I just picked up a nice set of 1966- 67 style low back bucket seats for my dart. I'm curious if anyone has tried to put seat back locks on this year seat frame. I think 1968 was the first year of government mandated seat locks.thanks!

http://columbiamo.craigslist.org/cto/4362244257.html Its rusty but looks pretty complete. Guys asking $4500

I love vipers :prayer:

Has anyone used these? I scored an upper and lower nos Moog ball joint set. I came with these HP adjustable upper ball joints.

I'm trying to figure out who sells the most correct looking factory steering and front suspension parts. Seems like most parts are either cheap Asian parts or geared toward performance upgrades. Ive been leaning towards Moog. I've seen some nos mopar steering parts pop up on feebay for crazy...

there is a 1969 dart gts 383 block for sale on ebay. thought id share it for you guys looking for your original block. Link: http://www.ebay.com/itm/1968-1969-A-body-Mopar-383-Block-Crank-Pistons-And-Rods-/161106799930?pt=Vintage_Car_Truck_Parts_Accessories&hash=item2582b6ad3a&vxp=mtr

This is something you never see for sale!1969 Dodge Dart GTS Convertible 340 4-speed. 1 of 58 http://madison.craigslist.org/cto/4053917013.html

I've been eying a stock radiator for my dart on an internet site. They seem to be very hard to find for some reason. The guy wants almost $400 with shipping for a used untested radiator with the right numbers on it. Is there another option out there for a stock looking radiator that accepts the...

Saw this on ebay. Not my car just sharing!She is rusty but it looks like he has all the hard to find parts. http://cgi.ebay.com/ebaymotors/Plymouth-Barracuda-CUDA-1969-plymouth-barracuda-440-m-code-cuda-/281161528981?pt=US_Cars_Trucks&hash=item4176887695&vxp=mtr

Anyone mix up Y2 yellow in ppg dbc 2000? My local paint shop says it only comes in the cheap omni brand. Any help would be appreciated . Thanks