Search results for query: *

Looking for a useable factory 727 SB dipstick and filler tube for my 74 duster 360. I bought an aftermarket one like the one in the photo and it just doesn't fit properly. Thank you... Would need it Shipped to 89130 Las Vegas Nevada.

Oh John, thanks just lmk I'll be down in Henderson tomorrow I can swing buy if you have one

Awesome just lmk!

Hey John do you have one for a 727 small block? The one I got from you is for a 727 BB Trans it won't fit properly the screw holes don't line up. I need one like this in the pic. Thx

Oh wow I'd love to see that! I'll send you a pm

Holy cow what luck! I'll take it. Could we meet up in Henderson next Saturday morning?

Looking for a dust cover for my 727 Trans, 360 engine. Shipping to 89130 Las Vegas Nevada Thanks!

Ok, thanks for the reply

Good Running condition or does it need rebuilt?

Looking for a running ready to drop in 360 long block, stock is ok, I’m on a budget as most are. Need it for my ‘74 Duster. located in Las Vegas NV, need local pickup Thanks

trying to spend less than $2000 if possible

Thanks Jake, I will keep that in mind

Thank you, I have been in touch with him.

still looking i do have a few local leads but nothing in stone as of yet. Trying to stay local as I dont have the means to pickup out of town as I need to see the engine first and hear it run if possible.

Is it complete carb to pan? Has it been fired yet, after being built? If you have any extra pics of the motor and build info, can you pm them to me. I live in Vegas, Thanks

Are you willing to sell the "built 360" separately?

Looking for a complete Carb to pan good running 340 or 360 engine, any year, in Las Vegas NV. will travel for right deal to So Cal or AZ\UT Need one that's ready to drop in and drive. LMK via a pm, thanks

I just wasn't patient enough to wait, my loss. you just needed some more time to finish it from what I remember. My car has been in the shop, one week after I bought it and its still there. Its not a bad car, I just overpaid for it and it needs allot of work for what i paid for it.My fault. I...

I should have been more patient, and bought this car. You did nice work, i really like it.

well, as far as the timing chain goes, the car was lacking power and yeah it did well on my 300 plus mile trip home but I think the trip was just too much and brought all these issues to the surface. From a dead stop the car wont even break the rear wheels free at all. I thought maybe just a...

well...I didn't do my homework well enough and got taken by the high of the buy. I am man enough to admit i screwed up and made an expensive mistake. Go ahead, tell me "I told you so!" :mob: Needless to say I feel really dumb:( Dont get me wrong I like the car but haven't been able to even...

Did you ever get the other wheels installed?

Well my battery hold down broke so I ordered a correct repop. So bungie cord for now to hold it hahaha Changed out the plug wires and added some heat protection sleeves. I’ve always had good luck with summit racing brand of 8mm wires plus the price is right. The old MSD wires used to be blue...

Basic maintenance this evening after work. removed and cleaned and re-gapped the autolites. New Wix 42044 air filter. I Installed a battery hold down as there wasn’t one there at all when I bought the car this past Friday and cleaned the battery terminals, added some dielectric grease, and put...

I found this on eBay says it has the correct size a 7 inch j hook for the drivers fender...the ones I had were 10 inch and I cut the excess off with a hacksaw 70 71 72 73 74 75 76 Battery Tray Hold Down Duster Dart Charger Cuda A B E Body | eBay

Ok, the J hooks I had were long so long that the one on the drivers fender, the wing nut wouldn’t tighten it down as it ran out of thread. SO, I added a few washers and nuts to close the gap, at least for now my battery is secure and it isn’t going anywhere. Removed that stupid battery handle...

ok cool I was wondering what that hole was for lol, thank you

I went and got a battery hold kit at pep boys, your standard J hook set up with a rubber brace that goes across the top...my problem is there isn’t anyway to hook the j hook to the bottom of the battery tray as it’s flush with the fenderwell. No way to hook it to anything! Any suggestions? I...

That’s my guess too...I had actually done the same thing in another car I had but I gave plenty of length of wire just for this reason m. I mean come one put a little extra wire there! It barely comes out the side of the console I have to reach my right hand in to hold the socket so I could pull...

Cleaned up the engine bay a bit and gave her a bath.