Search results for query: *

  • Users: wireweld
  • Content: Threads
  • Order by date
  1. W

    Adjusting mc pushrod

    I am installing a 15/16 wilwood master cylinder in a 72 Dart. Manual brakes. KH disc front and dr.diff disc rear. The mc comes with the pushrod installed and is adjustable. I'm looking for how is the best way to adjust the pushrod and how to know when it is adjusted properly. Never done this...
  2. W

    What rear gear?

    What rear gear would you use for a street performance car with an 8 3/4, 200r4, and 29 inch tires? I have 4.10, 3.55 and 3.91. 72 Dart.
  3. W

    Flexplate

    Will an out of balance flexplate cause vibrations under load but not when revving engine in neutral?
  4. W

    Bushings for Dillinger arms

    Where can get bushings for Dillinger lower arms?
  5. W

    Under hoist stands

    I was wondering if I could support the car on 4 tall stands when lifted up on the hoist? I want to check pinion angle. I would put 2 under rear axle and 2 up front on the frame. Thank you for any advise.
  6. W

    8 3/4 center

    Setting up the center with new 4.10 gears and bearings. Set pinion preload to 25 inch pounds. Depth gauge said I needed .096 shims. After setting backlash and preload on carrier, backlash set at .006, and tightening cap bolts. I checked backlash and it was .005. the setup turns hard by hand . So...
  7. W

    8 3/4 center

    Looking for someone who can set up a center section for me in eastern South Dakota. Any suggestions.
  8. W

    [WANTED] Pair of Kelsey Hayes disc spindles

    I need a pair of KH spindles. If you have any please let me know. Thank you.
  9. W

    Column shaft

    I have a floor shift column in my car, 72 Dart. The bottom part of the shaft that goes into the box coupler is round and looks to be welded into the steering column. Can I cut the weld and pull the round shaft out and weld dd shaft in its place?
  10. W

    Reaming spindle

    When reaming spindle from small joint to large joint, do you drill the hole thru the spindle for the minor diameter first? And then ream?
  11. W

    [WANTED] Kelsey Hayes brake pad clip

    I need 1 clip that holds the pads in the caliper. Let me know if you have one. Thanks, Ed
  12. W

    [WANTED] firm feel upper control arms

    Looking for firm feel upper control arms with small ball joint. PM here. Thank you.
  13. W

    Hub to hub measurement

    What is the hub to hub on a 72 Dart with Kelsey Hayes disc brakes?
  14. W

    Who in South Dakota ?

    Can narrow an 83/4 housing? Also is there anyone that can change bs on a pair of wheels?
  15. W

    cam change

    Combo: 416 hughes eddy heads cnc flowed 297 @ .600 lunati voodoo 255/263@.050 .616 lift 110 lsa 12.4 cr E85 1 7/8 TTI headers 31/2 collector dynoed at 651/575 with super victor, now using performer rpm Thinking about grinding a cam with the same specs just changing the lsa to 114. What do...
  16. W

    Intake angle ?'s

    I am changing to a dual plane from a single plane. My question is: I will have to mill the intake, since my heads have been milled. Will a machinist be able to measure how much to mill the new intake by measuring the old intake?
  17. W

    [WANTED] Ring and pinion

    Looking for 3.91 or 4.10 ring and pinion for 741 case.
  18. W

    8 3/4 center setup

    Anyone in SE South Dakota who could setup a sure grip center ? Thank you Ed
  19. W

    Coolant sensor

    I am looking for a coolant temp sender that is closed when coolant is cold and opens when coolant is warm. Around 150 to 170 degrees. Does anybody know where I could get one?
  20. W

    [WANTED] buddy seat

    I am looking for a buddy seat for an a body. With mounting brackets if possible. Thank you. PM me here.
  21. W

    K member spacers

    Can I use 1/4 inch spacers under the k member mounts to lower the k for header clearance? I have tti 17/8 headers and the draglink is touching at full left turn.
  22. W

    Dillinger chassis

    Any updates on him? Just wondering if still building control arms.
  23. W

    Rally wheel help

    Does anyone near Hemidenny have a 15 x 7 rally wheel with 4.25 bs that he could test fit on his k frame. This is the size wheel I am using and would appreciate anyone that could offer the use of their wheel for this.
  24. W

    Ez efi 2.0

    FAST™ EZ-EFI 2.0® Self Tuning Fuel Injection System Tagged under: Racing & Performance Company Media Contact Information Memphis, TN – The next generation of the revolutionary self tuning EZ-EFI® system features ignition control, a refined, higher flowing and higher horsepower...
  25. W

    Intake manifold

    Where can I get a intake manifold like the edelbrock pro flo xt made for a small block? Edelbrock EFI Chrysler Intake Manifolds PRO-FLO XT MANIFOLDS For 440 Wedge Chrysler (1500-7000 rpm) The Pro-Flo XT intakes are engineered with a large plenum and long tapered runners to deliver maximum...
  26. W

    vibration dilemma

    When I accelerate up to about 3500 rpms it is smooth as glass, but after 3500 it starts to vibrate. At 4000 and up it is shaking the whole car and I could only take it to 4500 cause the vibration is too much. It vibrates on decel down to 3500 and then it is smooth again. The driveshaft is...
  27. W

    Cope CRT-22X

    Less than 500 miles, never raced. 200.00 plus shipping. Located in South Dakota. Fits 904, low band apply. Reverse pattern, full manual.
  28. W

    wilcap adapter

    I thought that I would start my own 200r4 swap thread. Here are pics of the wilcap adapter.
  29. W

    slip yoke movement

    How loose should the slip yoke be in a 904 tailshaft? I can move the yoke up and down in the tail, shouldn't it be tight?
  30. W

    2.94 suregrip

    I am looking for a 2.94 clutch type sure grip for an 8 3/4. I will consider the open carrier if it is for the 741. Thank you
Back
Top