Search results for query: *

Thanks for all your information. GTX John, You said they make a good race car have you seen any doing auto cross? Just curious how they would do. Thanks. KB9GIB

Ok thanks I’m a B body guy so thanks for heads up.

Where can I find info on this car I picked it up cheap today thanks for any information.

Thanks for all who have help me out on this I haven’t been on for a while I super busy at work. Thanks again KB9GIB

I’ll look closer tomorrow. It has some sort of spring L on the jaws also? I have never run into something I couldn’t figure out until now maybe it’s just so simple I’m over thinking it. Thanks KB9GIB

Can anyone show me how to use the Delphi crimpers? We bought them from American autowire I cannot find nothing on YouTube any help would be appreciate. KB9GIB thanks

Some good ideas. Thanks

We are putting in Holley sniper system. looking for where you guys hide your ignition box & ignition coil? I was thinking maybe inside the car? If you have any pictures would be helpful. Thanks in advance. KB9GIB

rmchrgr, Thanks for some wiring information I never rewired a whole car before so I say it’s going to be a learning experience for us my son has also added the aftermarket A/C also so I might not have any hair left when we get started on the wiring. Thank you again. KB9GIB

I thank all that has replied. we have been talking to EFI system Pro. We are doing all new American auto wire so hopefully that will take care of the wiring. And going with a complete system from fuel tank to distributor. I’m sure I’ll have more questions when things get started. Thanks KB9GIB

I’m needing some thoughts on EFI. my son is going EFI on his 340 Demon 20 over J heads small cam. If you where to buy today would you go (Fitech) or (Holley sniper)? Holley is about $400 higher if I looked at it right. Thanks in advance for your input.KB9GIB southern Illinois

Thanks I’m going to call and check the cam spec. Thanks for all your information and help

I think you all for the information I have tried looking the cam spec up but didn’t have any luck. Thanks KB9GIB

I appreciate your thoughts Do you think the heads and intake are ok for this motor? We have it out of the car now was putting a 340 in it but the machine shop has yet to get the work done. so we thought we would just put the 318 back in till winter. I just always thought it was probably the...

My son has a 1970 318 in his demon. we have a set of 302 heads on it I think the intake is elder LD4B, elder 650 carb, only number I find on the cam is EDEL 955836, I can’t find any spec on it with 323 gears. This thing starts runs out good but will not get out of its own way. So just looking...

Thanks for all the information. KB9GIB southern Illinois

I’m using Green plastic gauge.

Ok I really appreciate your help. Thanks KB9GIB

Ok guys this is what the green plastic gauge shows. Is this within range? my son and I are just trying to make sure on his motor that it’s right. I appreciate all your help. Thanks kB9GIB

Can someone tell me on a 340 bearing clearances stock crank & rods turned 20 using clevite P77 bearings what should the clearance be rod and mains. Thanks for any information in advance. KB9GIB

Sorry I haven’t been on for awhile I don’t have a closer up picture but yes it is wood grain across the front of the dash I went to a place that does vinyl wrap they can print you off what ever you like I think payed $20

Thanks for that information I will use the looser ring gap. Thanks again KB9GIB

Ok thanks, I checked the instructions they show .0065 for street. and show .0080 for street@towing. Times the bore for gap. Just thought I just ask for reference. Thanks for your reply KB9GIB

Need advice, 340 motor been bored.20over KB pistons just a street car what would you guys that are motor builders (Gap the rings) car will be fuel injected. Thanks in advance KB9GIB

Thanks for the information. KB9GIB

Thanks

Need some information putting my son’s 340 together do we want bearings with the (dole holes?) H-P-? Style bearings. I’m lost on the dole hole and the type of bearings as the H bearing are P bearing. Thanks for your help in advance. KB9GIB

Ok thanks that’s what I was looking for. KB9GIB

Anyone know where to find (Bucket seat track studs?) I was thinking a carriage bolt but they look a bit different thanks in advance. KB9GIB southern Illinois

Ok thanks I appreciate your information very much. KB9GIB