Search results for query: *

Selling my Dart. http://atlanta.craigslist.org/nat/cto/5094436680.html But, for any FABO member I'll sell it for $1000! Just come and get it and drive it home. I'm in Georgia about an hour+ north of downtown Atlanta. Found another car I want.

Few months ago replaced the radiator, water pump, thermostat, hoses, etc. Had a 160* thermostat and when cold weather came in, upped it to a 180* to get more heat flowing. She's always run around 180*-185*. As the temps rise, I've noticed she's running hotter as the heat rises. When it was...

Putting the timing cover back on after replacing timing chain and, of course, twisted off a bolt. Tried unsuccessfully to get the bolt out so had to drill and put in a helicoil (see circled hole in pic). Drill/tap went all the way through into what, I'm assuming, is a water jacket passageway...

So I put a new timing set on the slant and short cut the timing cover gasket so it leaked. Never enough time to do it right but always enough time to do it over, right? So now I'm pulling the oil pan too and doing them both right. When I got the timing cover off I noticed the chain didn't...

I've read a dozen threads about needing the oil slinger. I replaced my timing chain and don't remember seeing one on it. Now I've got an oil leak and going to pull it again and replace the gasket. After reading through all the threads, I'm a little confused about the orientation of the oil...

Just so I don't have to retype and repost all of the pics of this, see my Craigslist ad. https://atlanta.craigslist.org/nat/cto/5002589172.html VIN/Fender tag: LP23: Dodge Dart,Demon Premium 2 Door Hardtop C4B: 225 105HP(net) 1-1BBL 6 CYL 1974 Dodge Main, Hamtramck, MI, USA 370442: Sequence...

Installed 4 pin HEI module on inner fender and moved coil up on top of inner fender too, about 4 months. Left old Mopar coil and ignition in place, disconnected, just in case the HEI module fries. Already happened once (my fault) and saved my rear. Got new Aurora plug wires and coil wire is...

My belts are in sad shape, only have lap belts, and looking into aftermarket seat belts. Looks like my front have the shoulder bolt up high where the windows join but I can't see anywhere there was ever a pivot for a shoulder belt in the back seat. Did it come with them, were they an option...

Fits a '74 Dart. Condition not important as long as it's not warped, the flanges are flat and none of the holes have been drilled out. I'll blast it, paint it and put a new seal in. Paypal preferred but not mandatory. Thanks!

Is this a decal and is it available anywhere? Mine's faded, scratched and you can't even see the "DODGE" anymore. Anybody refinished or modded theirs? Thanks to all for any input!

Gaaaahhhhh! I hate bulkhead connectors. Just got my tyranny rebuilt and drove her home from the shop. Pulled in the driveway to check the fluid and everything was fine. Killed her, went in the house for a cold drink, feeling good about life and my wonderful Dart. Went to start her up and...

Daily driver, bone stock, nothing fancy. Which torque converter would you pick? I believe it's a 10-3/4"? What particular specs should I be targeting so I'm sure I'll get the correct one? Thanks for all input and advice!

Last October I pulled my engine and transmission and replaced all my seals and gaskets. Tranny went from leaking a quart a week to zero leaks since then. Today I drove to the auto parts store and picked up a quart of oil (didn't quite get all the oil leaks stopped). On the way back I stopped...

My car originally came with the map light option. I have a toggle switch on my lower left dash that has a bezel with "map light" on it. My question is....where is it and what does it look like? My car is missing a lot of interior pieces so I don't know if it's missing or not. It would help...

I have a '74 Dart "Special Edition" with the deluxe chrome trim package around the top of the doors, under the weatherstripping. Was this on all cars? I have rust issues and the drip rails have been removed. How do you remove this trim? Do you just pry it off, I can't see any screws unless...

'74 Dodge Dart. Passenger side door pull handle. Need the cap that covers the screws. First pic is what I need, 2nd pic shows it missing. Condition unimportant, just want to cover up the screws. Anybody got one? Thanks!

I know this has been beat to death and I'll probably get flamed for starting it up again but here goes. I want to install a 90A+, internally regulated alternator, preferably Denso or similar case so I can use my existing /6 bracket. I have searched for 5 hours, here, slantsix.org, allpar...

The old girl was sadly abused when I got her with no external emblems and painted with a paint brush and roller. This spring I'm going to sand her down and just shoot some "hot rod black" on her just to clean the POs mess up somewhat. She has holes in her fenders and hood where emblems once...

Tempting. About 45 mins from me. $1000! Given the area and people there, $750-$800 would probably get it easy. I already have too much going on or I'd jump on it. Just thought I'd broadcast it for everybody else. http://atlanta.craigslist.org/nat/cto/4818678686.html

First 4 months I had her. Water leaks, oil leaks, tranny leaks and p/s leaks. All fixed now but she definitely marked her territory. It'll take all summer before the grass recovers. :)

Had a leaky pressure hose. PO had cobbled together various fittings to make an incorrect hose work. Before I chose one I searched here, slantsix.org, allpar, and googled for hours trying to make sure I got the right one the first time. Never did get a definitive answer so I took my chances...

'74 Dodge Dart, 225 /6, A904. Federal p/s pump. High pressure line. Don't you just love PO crap. Been chasing a power steering fluid leak for weeks. Replaced the pump...

The plastic bushings that go on each end of the Z-bar rod. The retaining ridge on mine has worn down so now the bushing slides out of the bracket and down the rod occasionally. Makes PARK more of a "suggestion" than a "command".#-o Anybody know where I can find any? Thanks to all for any help!

Just thinking to myself. If this /6 ever dies (which it probably won't any time soon) do I HAVE to change K members to a small block style or can you drop a small block in and fab/weld motor mounts to the /6 K member?. What are the problems you run in to? I have some nephews that are Mopar...

Having a weird thing happening recently. I installed a Sunpro voltmeter a couple of months ago and things have been running well. Since I bypassed my original ignition and installed the HEI ignition module setup, she's been getting a good 13.5v at idle and 14.5 volts at rpms higher than 700...

Just finished installing HEI igntion system and left OEM ignition system intact so I can swap back and forth easily in case something goes wrong with the HEI. Noticed immediate difference in the way she runs even with the old plug gap. I'll be installing new cap/rotor, 8mm plug wires and...

'74 Dart, 225 /6, A904. Doing the GM HEI conversion per the slantsix.org instructions. http://www.slantsix.org/forum/viewtopic.php?t=15779 My intention is to install it on the passenger fender, use the original switched 12v at the OEM ignition circuit, and put my full 12v from the alternator...

Just thought I should share with you guys my experience. Sending unit was non-functional, turned out to be a missing float. Bought this replacement http://www.summitracing.com/parts/rsd-ysu6301/overview/year/1974/make/dodge/model/dart Worked well and fit perfectly. Problem was it leaked...

'74 Dart. The reason I'm asking is I've already bypassed the ammeter and have a Sunpro 3 gauge set installed just kinda hanging off of my dash. It occurred to me that the gauges are the same size and the OEM ammeter, water temp and oil/brake gauges. Since the factory gauges are wired in the...

'74 Dart, 225 /6, A904, factory AC/heat. My fan switch only functions in low/med speed, I have no high speed. Before I tear this puppy out, anybody got a photo of how the fan switch is mounted to the controls? I can get a new one for under $20 bucks...