Search results for query: *

  1. T

    [WANTED] W2 Small block exhaust rocker needed

    Rocket, I cleared my PM messages. Left you a message.
  2. T

    Rocket, I figured out how to clear my inbox.

    Rocket, I figured out how to clear my inbox.
  3. T

    [WANTED] W2 Small block exhaust rocker needed

    So I'm an idiot. I can't figure out how to delete old PM messages
  4. T

    [WANTED] W2 Small block exhaust rocker needed

    These are the rockers for W2 race heads and not the econo W2; correct?
  5. T

    [WANTED] W2 Small block exhaust rocker needed

    Does anyone have any blue Mopar or Gold Crane 1.5 exhaust rockers for W2 heads? This the offset shaft style used with aluminum rocker stands.
  6. T

    Stroker kits, Ohio Crankshaft vs Hughes Engines

    I'm looking at big inch SB stroker kits from Ohio and Hughes based on a 360 block. Ohio has a 4.1 inch crank kit that'll go 425 inches with a 4.060 overbore, (418 with a 4.030 bore). Hughes is 4.180 stroke with a 4.030 bore for 426 inches. This will be a drag race only engine in my Dart. I'm...
  7. T

    How do hydraulic flat tappet lifters fail?

    Are you using a high zinc oil?
  8. T

    Alternator mounting with Moroso electric water pump kit

    I assume it's this pulley. Only one that Moroso shows.
  9. T

    Alternator mounting with Moroso electric water pump kit

    I meant the passenger side, not the drivers! Dislexia!
  10. T

    Alternator mounting with Moroso electric water pump kit

    Guys, Thanks for all your comments! It looks like I'll figure out a mounting in the normal drivers side area. I'll use a smaller pulley as suggested and will have a cut-off switch for the alternator while racing, which should keep the belt on! Any pictures of your installations would be...
  11. T

    Alternator mounting with Moroso electric water pump kit

    Do me a favor and send me a picture of the mounting of both the alternator and water pump. I'm trying to figure out which mounts to buy, and I really don't want to spend a lot of money if possible!
  12. T

    Alternator mounting with Moroso electric water pump kit

    Anyone running an alternator with an electric Moroso belt driven water pump kit? I have a 68 Dart race car with a 360 LA motor. I've been running no alternator for 14 years of racing, charging battery between rounds with no problem. However I've decided to add an alternator to speed up...
  13. T

    W2 head installed valve spring height

    I've been toying with buying a spring tester. I'm going to know. I'm going to spend a little money and get a good one. I'm being educated. Thank you guys for your comments and help.
  14. T

    W2 head installed valve spring height

    So using your equations I come up with different answers. 124@1.80 310@1.25 186/.55 = 338 lbs. 133@1.88 354@1.28 221/.60 = 368 lbs. Am I missing something?
  15. T

    W2 head installed valve spring height

    The 120 seems too low for me as well. I'm confused about the 540lbs/in. Where is that?
  16. T

    Is a 75 360 LA supposed to have a oil slinger?

    So I'll add a little here. I bought a 360 crate motor from Mopar Performance about 16 years ago. It didn't have the special bolt with the hole in it for oiling. It also didn't have the 9/16 plugs in the block behind the plate. Look at some of the posts on this website and you'll see plenty...
  17. T

    W2 head installed valve spring height

    This is the book that I have. It was edited by Larry Shepard. I'm not sure, but I think it might have superseded the book you have. Anyway see below. Thanks to both of you for your comments and such. Great info! I appreciate it. On page 203, this is what is said about the P2946353...
  18. T

    W2 head installed valve spring height

    Interesting. MP performance book recommends these springs for this cam and others. When you say MP engine manual, I'm not familiar with that. Where'd you get it?
  19. T

    W2 head installed valve spring height

    It's a solid flat tappet. Where did you get those spec's?
  20. T

    W2 head installed valve spring height

    I've been going through my old posts and updating them. I installed that Lunati cam, lifter, spring, kit in November of 2013. It's first hit at the track was the Thanksgiving race at Las Vegas. It was a disaster. It bent several pushrods and destroyed 2 rockers. I had checked for clearance...
  21. T

    590 cam installation tips

    It's been a long time since I first posted my question. Well... I've finally installed the cam in the engine and taken it to the track. It was installed straight up. Ran a 10.95 in a head wind letting off the throttle in Phoenix. I haven't been able to race since due to the COVID-19...
  22. T

    Quick Change LA engine timing covers

    Does anyone know if a quick change timing cover is made for the LA engine?
  23. T

    [WANTED] W2 valves needed

    A set of 16? What do you want for them?
  24. T

    [WANTED] W2 valves needed

    I need at least one W2 head exhaust valve. Part# P5249197. It's a 1.60" valve 5.29" long. I'll buy all you have. I'll also buy 2.02" intakes, part # P5249195, but I need an exhaust valve immediately! Thanks! Tim
  25. T

    [WANTED] P2946353 valve springs

    I need 16 of part # P2946353 Mopar Performance Parts valve springs. Tim
  26. T

    [WANTED] Centerline Autodrag wheels

    Say 5"? What Back spaces do you have? Do you have any fronts in a 4.5 pattern around 3.5" or 4" width?
  27. T

    [WANTED] Centerline Autodrag wheels

    Centerline Autodrag wheels, 15 X 10 with 4.5" bolt pattern. Need 2 please. Tim
  28. T

    590 cam installation tips

    Oh yeah, car weighs 3,180 with me in it. I also always degree any cam I put in for accuracy.
  29. T

    590 cam installation tips

    So for all here is my current combo. .030 over 360. W2 (long valve) small chamber (57cc) mildly ported heads with Crane W2 roller rocker setup. Mopar 557 cam at present, straight up. Had pushrods custom made for length to determine proper rocker and tip geometry. Will do so for the 590 cam...
Back
Top