Search results for query: *

Thanks for the info everyone. The more the better.

Mopar65, if you go to the page he told you to go to and look on the right side of the screen, there will be a download option. Click that. I think it'd be a good swap, especially with the OD.

I've looked and cannot find your username on the Jeep forum, even when using the member search tab. I'll keep looking though.

Ok. Thanks! EDIT: Do you know if there's a way to search for usernames on that site? Otherwise ill just scroll through each section until I see a post by you.

This isn't going to be a swap that is happening immediately, so take your time on finding the files. Ill definitely look over on the jeep forum. I'm not sure if the diagram for the Cherokee would help or not, but it might. Thanks!

Thank you, 67Charger and 5.2jeep! 67, I will definitely be looking that over! Thank you! And no worries, I have no plans of making money off of doing this! I plan on using for personal and helping out friends. 5.2, I'd still love to see your notes since they're OBD1. Thank you both!

I'm sure they'll let you look at it. If they have an electronic version, see if they'll print the page off. A friend has access to a 94-97 2500 with a salvage title but it only has 88k miles on it. He would like to swap the 360 from it into an 85 d250 so i'll be learning OBD2 wiring as well...

Thanks for the replies, guys! JD, I'll definitely check that thread out. When I find (or make one) I will be sure to post it. Dragbaron, I have a place that I can go to access Alldata so i'll do that. The stuff I was more concerned over whether to keep or remove was like for the evap system...

Are you still building the magnum harnesses? Shoot me a PM if you are. Thanks!

Alright.. I've looked everywhere and have yet to find the information that I, and I assume others, are looking for. There are tons of write ups on swaps focusing on the physical swap. I can handle that part, but I'm more concerned with the wiring aspect. I've seen Magnum Mopar's harness and...

I don't recall what pan was on the engine and I probably couldn't identify it in my pile either. The engine wasn't out of an A body so it probably wouldn't help you anyways. Wound up slapping the engine in my buddy's 68 satellite trying to get it ready for HRPT. Sounded good for a bit and then...

Sold!

Hey everyone, I have an old Edelbrock TR5 tunnel ram for a small block. Picked it up at a swap meet a few years ago just because I thought it was cool, but I don't really need it. All of the visible boltholes are in good shape. I haven't pulled the water neck off to see how those threads are but...

Well, I decided to go ahead and do the swaps today and everything went smooth. I remembered that I bought a BB case at a swap meet about 3 weeks ago, and decided to put the CC guts into it since I already have plenty of small block transmissions. The BB trans had an accumulator blocker rod in...

I will do that. Thanks for the info!

Hey everyone! I'm going to put a 383 and a motorhome 727 into my club cab truck. Club cabs have a 2 piece drive shaft and a short tail shaft. My MH trans has the "intermediate" tail shaft (Longer than the short, but shorter than the regular slip yoke type). I have an extra good small block...

Pulled the transmission earlier, which is extremely easy on a truck, as it doesn't have a crossmember. Got it out and found that the input shaft on the 230 is about 1.5 inches shorter than that of the 745. The 745 uses a different clutch spline, and a much larger throw out bearing. Stuck the...

I found that I have a good A230 I can use. I'll need to dig out a bell housing like in the truck to make sure it will bolt up, unless anyone knows off hand. I assume the linkage is the same and will hook up to the 230? I'll measure, but both transmissions look the same length, so the...

Yeah, the 745 is pretty heavy. It does have a tin top cover, and a hump in it since its a 745. I might have an a-230 or two, ill have to look through the pile. Those should all be syncro, from what I have gathered.

Damn. Thanks for the info.

Hey, I've got a 3 speed out of a 67 dart. It was behind a 273 that I bought a while back, and I haven't needed it until now. I need to know if this trans is has a syncro first gear. It will be going in my 67 truck, which at 350k has a bearing going out, and doesn't have syncro first which is...

Once I find a pan and get it in, I will update how it runs. Thanks.

Get ready for a long post.. At the local yard, for the last six months or so there has been this 383 missing one valve cover and no distributor or carb on it getting rained in. Thursday afternoon, something told me I should go buy it. Went out there and bought it for $80, which I thought...

I do still have it. Send me a PM if interested! Thanks!

Why wouldn't a square bore Holley fit it? I believe they came with AFB's (Maybe WCFB's, not sure) from the factory and they have the same base as a Holley.

273 intake is sold! Carb stud on tunnel ram has also been removed.

Krazykuda is correct. This intake will only work on 64-65 engines. Thanks!

Hey everyone! I've got a Formula S barracuda (Commando) intake for a 64-65 273, as well as a dual quad tunnel ram for a 318-340-360. I purchased a disassembled 273 a few years ago and the intake came with it. I assembled the long block, went to put the intake on, and was confused when the bolt...

Alright thank you.

Oh, no It's not in the truck. I'm trying to find out if I can modify an Ultra bell for a 904 to use with a 518, as you're supposed to use one for a 727. Motor isn't in truck and I don't have a trans for it. I don't want to do anything with the inside of the transmission if I find a good used or...