Search results for query: *

318 magnum cam 432 lift single pattern / timming set single row , chain stamped made in usa / valve springs,retainers,locks. all were new in remanuctured motor by ac/delco. Motor never run, I installed new cam setup in motor $190.00 or Best offer plus shipping or seperate cam and springs...

I have a couple posts but different subjects . This for cast crank 340 flywheel. Any way to Id one. No numbers on mine but has 3 drill holes on back , just want to check before new clutch put in . Did have vibration new driveshaft but have to do pinion angle too. Way off.

Hello everyone, I was having problems with clutch engagement was trying different fork pivots but couldn’t get fork back in with new pivot. I pulled trans a833 and bell trying to figure what bell this is to match some parts. Came off duster with 340 motor . No numbers on bell , all steel...

Hello everyone , hope your all safe. I have clutch fork ratio problem. 73 duster was a slant car now has 73 340 4 speed. Got it as unfinished project. Clutch issue, pedal almost to floor to dissengage. All adjustments tried new linkage clips and washers . Bell housing is an oddball lakewood...

Hi Everyone Happy Holidays, looking for 833 slip yoke 30 spline, needed for 73 duster 340 4 speed 8 1/4 rear, car had wrong driveshaft, too short, drive shaft shop said yoke is bad cups too loose, were going to make new shaft, but yoke bad, and price to make everything 525.00 so looking for a...

Looking for clutch pedal that had 6” between the pins. Mine is the 5-1/4” pedal need some more throw on pedal for diaphragm clutch. Thanks. Located in nj 08827.

Hello Everyone ,looking for wiper switch 3488839 for 73 duster 2 speed motor Thanks

Hello everyone, I am installing new style wiper motor wpm380 2 speed , bolts up fine has 4 prong plug like factory, no directions of course , has anyone hooked one of these up? old wiper motor was missing, factory manual show a ballast resistor mounted and wired in harness for low speed...

Looking for wiper motor crankarm number #3431741. This is for 73 duster 2 speed motor. Thanks

looking for wiper motor crank # 3431741 and if crank arm has spring clip as well Thanks

Hello Everyone, I am looking for info for wiper linkage for a 1973 duster 2 speed , I tried a set from earlier style A bodies but they seemed short and changed clocking of arms. had black plastic snap bushings , part numbers show they fit 67-72 A bodies. Are 1973 and up linkages different ? i...

looking for wiper linkages for 1973 and up A body 2 speed with motor crankarm, or part numbers . car is missing parts and motor , any part number info would be appreciated as well Thanks

Hi everyone. Looking for 2 speed wiper Motor with all linkage to hook up to wiper arms studs for a 73 duster. I am in nj close to Easton pa. Hoping for local pickup if possible, but will travel to pickup Thanks. No parts found at Carlisle.

looking for hood hinges with springs for 73 duster. im located in n w jersey by pa would like to pick up if possible .

1978 mustang no rot , super solid , factory 302 car auto, has 71 302 , 4 barrel, and factory 4 speed setup ,dual exhaust, just rebuilt trans , power steering/brakes. 8” rear Ac car. Included but not installed, runs strong drives well, very dependable , could use front end work , but very...

Hello everyone, was looking for some opinions. I picked up a new in box 8534 MSD pro billet non vacuum distributer for $100 . couldn't resist price. but need an ignion box and coil. was wondering if i could get away with putting gm hei module in and coil. or should i get summit box and coil,or...

Hello Everyone, got a question on a 904 rebuild, the stock direct clutch inner and outer seals are wider than new replacements that came in kit, performance auto 12701, are they a problem ? or just put in . The original inner seal number is 1942396 , only available as nos, the new inner seal...

vararam intake assembly great shape , for 2009-2017 dodge ram hemi trucks, local pick up only, zip 08827, new jersey $260.00

Looking for an 8.25 rear for an F body 67-70 b body8.75 rears or an a body should fit. 323-355 gears and sure grip are nice but not a deal breaker. Near or in nj north east by easton. Thanks.

Hi everyone , bought a used 904 was supposed to be rebuilt ,was used after rebuild, but there is some strange goo in pan and some water droplets in oil , only had a little trans fluid in it and seems dark , doesn't smell , but looks suspicious , jut looking for some opinions on possible goo, its...

Looking for a good 904 trans rebuilt or rebuildable. non lockup for v8 small block. In or near nj i am located in north west nj by easton pa thanks

Looking for for 8 1/4 or b body 8 3/4 to 1970. rear for an f body 323 - 355. Sure grip. Can be a open rear. Prefer sure grip. Near or in nj. I am located north east by easton pa. Thanks

looking for a project, looking to spend $3000 ,any motor as long as its a two door i am in north west nj , something reasonably close 2-3 hour distance would be great . Thanks for th ad

Hi everyone , hope our holidays were great. Ok , so here is the story , I sold my dart swinger to a local guy who "always wanted one", tell him everything about car and give him all the extras with it. two weeks later i see it on ebay , then on craigs with the cars discription more than...

1982 suzuki gs450t. Excellent running and riding. Everything works only 5700 miles , perfect seat , new battery, oil filter and oilchange, new air filter, carbs cleaned and new floats, bike runs like new, great classic bike. $1900.00. Bike is in hampton nj 08827 will trade for an A body as...

Looking to trade a 1982 suzuki gs 450t motorcycle. 5,700 miles runs and looks excellent value is $1900.00 for A body project car or slant6 car any dart , duster , demon , valiant , scamp. Or a B body. Can add cash also, have title in my name. Location is hampton nj 08827.

great driver, drive anywhere, has ps/pb 273 motor, nice lumpy cam, 904 with shift kit, 355 geared 81/4 sure grip , rear rebuilt , all new brakes, lines ,drums rotors , pads , calipers, bearings , wheel cylinders, master, booster , new tank, and lines, complete front end, new front sway bar all...

have a reman electronic distributer on a small block, checked shaftplay after 2k miles by hand, can touch pickup with relucter with little pressure, book says 1 pound, pickup plate seems to move pretty easily,flexing spring like.Question is is it worth trying to make this setup work better or...

anyone using spool mounts on a magnum motor?, I am putting a 5.2 magnum in a 73 dart ,can I use my old spool mounts or do I need different mounts . THANKS FOR ANY INFO

i picked up what i though was just an 833 a body trans ,it was rusty,brought it home and checked some more. Front retainer is over 5" and date on side cover is 4/28/76 gears have single notch so its 309 first ratio, beleive its an iron over drive ,its rusty inside ,is it worth rebuilding? or...