Search results for query: *

Heat Sink : 2 Pass 20" Heat Sink Transmission Cooler Kit Or https://derale.com/product-footer/fluid-coolers/transmission/frame-rail/13220-detail I've been looking at these for awhile now, anyone have real life experience with either style? Car is a 72 Demon with a 408, 727, 3.91 gear, mostly...

I'll provide as much info as I can, so this might be a little long. I'll just break it up into sections. VEHICLE: 72 Dodge Demon 340, purchased it back in 2013 with I believe a right stuff manual front disc brake kit. Decided to install the Dr. DIFF setup for better braking and liked the...

72 Demon, large bolt pattern, 8 3/4 rear end, disc up front, drum in back (switching to wilwood or other upgraded disc all around next year). Looking at a set of 17x7 +38 for the front, 18x8.5 +25 for the rear. The rear is stock tub and previous owner half assed the fender roll front and back...

Wasnt sure where to put this. I have a demon with an aftermarket floor mount gear selector. I want to install the column gear selector to floor shifter conversion on the column. Was wondering what to do to the neutral safety switch inside the column. It's there a by pass when installing the...

Just pulled it out of my 72 demon. Recovered in legendary vinyl and relaced the foam. All professionally done. Only issue is the seat back release button broke off. The back seat will still lock upright and fold down but the knob is gone. Trying not to ship, prefer local pick up, will travel...

planning on replacing my front bench with some procar 90 series buckets. when I do I want to upgrade the seat belts. is there a go to manufacturer for mopars? I've come across julianos.com and a few other manufacturers but wasnt sure if there was one better than the other when it comes to...

Tried searching the forum but nothing came up and i swear i seen it on here before, but is there a list of junkyard bucket seats that will fit in a 72 demon. I thought i read old jeep Cherokee seats work but I'd like some other options. Have to match the rear factory seat pattern if possible to...

72 dodge demon 340 with a 408 stroker and a 727. Here's some back story. i was coming from a cruise and immediately noticed it running rough. as i came to a light i noticed the headlights dimmed, it started idling rough and eventually died. It started right back up, put it in neutral and played...

Decided to re do the emblems, used flat sunflower, Chrysler engine red for the lettering and bright silver for the outline of the interior lettering. All the supplies where picked up at a hobby shop, all the paint is a lacquer. Brushes where 1/8, 1-32cy and a 970 atlas brush. The 960 needed to...

I have a cracked a arm and decided to go with some qa1 tubular a arms. While I'm in there I want to upgrade to the big bolt pattern so its the same front and back (dont ask, it came this way when I bought it). I have disc in the front now with what looks like newer calipers and newer lower...

So i just installed bigger jets to accommodate for larger headers and when i went to start it up nothing, no lights, no cranking, nothing. I checked my battery voltage it was good, gave everything a quick visual and nothing jumped out. Threw a jump station on and just kind of left it on after...

I was invited by pinckney dodge to have my demon in their booth 5/30 & 5/31 at the art in the park. They well need cars from about 8:30 until roughly 5:30. I'm only showing mine on sat. and they are fine with that. Over night security will be provided for those who want to leave it overnight. PM...

On the plug group in the middle, i had a blue female wire that was unplugged, i got the car back from a shop and it is now plugged into the small red wire from my msd box and now a female fitting with 2 black wires sharing one plug is hanging loose. I've seen plenty of the wiring schematics but...

wasn't sure where to put this, trying to decide on which fan to go with, oem mechanical, aftermarket mechanical (flexlite), electric. I have no shroud on it now, if i stick with mechanical its getting a universal shroud. I mostly do cruises and a couple times stuck in traffic its gotten a...

Any ideas or recommendations, dimple the header and shave the joint ? Not sure about steering box either. It's a demon with a 340 and auto trans.

Tried starting it and it gave me the same issue as about a week ago. I turn the key and it tries turning over real slow like the battery is dead and then just clicks. The voltage at the battery is 13+v. I tried jumping the starter relay, not sure if i did it right, turn the key to acc, take a...

I am planning on a full disc brake conversion on my demon, so I am also looking at a new set of wheels because of the switch from sbp to lbp. I'm looking at 17x7 4" backspacing 0 offset and 18x9 5.94" backspacing +24 offset. will these fit, i do have other options with the backspacing but i like...

i think the socket is bad, i replaced the bulb and still no signal but i get the passenger front/back and just the driver rear. I replaced the bulb and still nothing. i was looking at the socket but i couldn't figure out how to remove it from the plastic housing. is there an easier way to get to...

Happened on Easter, took the demon out, started and ran fine, shut it down after about a 45min cruise, temp only got to about 170. had to restart after less than a minute after i parked it and it had a very weak/slow start like the battery was almost dead. did a quick visual, checked a few...

what is everyone running? I am looking at the Mopar performance mini starter recommended on TTI's website. Any reviews?

http://monroeautoswapmeet.com/ all make and model not just Mopar

Trying to find a new set, I've seen plenty of chrome sport mirrors with the driver side remote but nothing paintable. Will sport mirrors from any other early 70's mopars fit (E body etc.)?

Considering doing the full power disc conversion on a 72 demon, what have you heard about them?

it looks like the knob/level whatever you call it snapped off. the metal is broken in half that attaches it to the rest of the seat hinge. any suggestions on where to find a replacement?

Wasnt sure where to post this, looking at a set of new tti headers and also looking at upgrading to power brakes. Am I going to have any clearance issues when it comes time to change spark plugs? Its a 72 Demon with a 340