Search results for query: *

That happen to me I had two bad alternators and ran into the exact same problems . Go buy a new altenator have them test it at supply house and make sure your getting around 14 volts . That should fix it. How this helps .

Daughters car lost reverse dropped tranny pan and filter was really bad looks like its been quite some time since its been replaced . The servo seems to be in one piece but new to Mopar cars , can anyone advise on what to look for to diagnose this ? I do have access to lift . The car seems to be...

Pm sent Thanks Bud

I'm very interested in the manifold ! It should fit in a priority box with a single fee . I'll pay your shipping thanks Bud

Where are you located and thanks

Thanks . Im looking into spray chrome kit to do some parts .

Is it chrome or silver . I would like to have it done ,but not sure if its like the armrest chrome or just silver . Thanks in advance

A member here showed me a amazing trick . put some super glue on the ball set your mirror and walk away . The super glue coats the ball and makes it large enough that you can adjust the mirror for about three to four months . then just reapply . Its clear and really tightens things up . Hope...

Probably need a fabricator . im not that skilled HELL yeah their paying . They tried to add labor for their attempt to replace it . I got on his butt and they agreed to reimburse me for the repair .

Long story Short , Daughter got a flat on freeway . I got it home and found out she missed school to go to local Aquarium in Long beach . I was pissed college first fish last { unless its her barracuda LOL} She goes American Tire and cant remove the spare tire I installed by hand with tire iron...

No leaks fits tight . Phista who makes that cap . I'm liking that look

Daughter lost cap , so checked Rockauto said they had it in stock , so I received it and was too big . Went down to pep boys and handed my ID to teller and grabbed eight caps . STANT 11705 fit real nice it's a little tight but fits with no mods Hope this helps

Stant 11705 . I bought at Pepboys in Los Angeles . I handed my Id to teller and took eight caps outside and that one fit great a little tight , but I know it won't fall off . Daughter lost the old one . I working on modifying a locking cap for her . Hope that helps

im interested in cali too . let me know if available please ill take them . Thanks Bud

I'll take them if you still have them ! Like and thanks Bud

Well this time I'm going to follow your directions step by step lol . I really appreciate your input . We finally got the electrical fixed . Interior was a pain but almost done just tieing up lose ends . I check the your info and get back tomorrow . Thanks Bud

Carter 2 barrel ,points wires are fine and it restarts right up . Hesitates also from stop then jumps like it should . Thanks for the replies . Confused about this- Could it be fuel sloshing and uncovering the jets when suddenly stopping?

Im back working on daughters Barracuda had electrical issues and got them resolved . Car starts and runs fine when warmed up but we stopped quickly to avoid car pulling out of driveway and it died . I drove it and and seems like if you stop at high RPMs it dies . Trying to get it reliable daily...

I'll take it if its available pm sent

Im located in Los Angeles can pick up . Lmk and thanks number sent to pm

They do make a locking cap (old school)?that is available at most auto supply stores for less then 10 bucks. Just peel the red sticker off and you have a chrome locking cap that seals . I will probally pick one up today and get you a part # . Called company and they have no clue , so I'm going...

Used dap weldwood red can only . Brushed both sides carpet and wheel well . Let it get tacky and start applying carpet . Make sure you pre cut to the finished measurement profit before brushing contact cement . Yes ,let sit in sun or heat it up . Apply heat gun for final placement and let it...

I in need of front drivers arm rest and trunk hinge for 65 barracuda . lmk and Thanks Bud

Carpet kit for 65 barracuda has wheel well covers can't get them to lay flat . Any advice is welcomed and thanks.

Doe's it have a spacer ? I took off the pasenger side control arm because the bushings are bad . The front bushing no problem ball joint was tough but no cus words . The front bushing was hell after beating the crap out of it with air chisel finally got it out ,but there's what looks like a...

Ok for now Im rebuilding 65 Barracuda front suspension . has anyone tried Sachs shocks on a Abody and if so can you give a short review ? I have heard Kyb's are too stiff and Monroes are a bit soft. i went with Sachs got them today. The car is a daily driver for a girl with a lead foot . The...

The BFH DID THE TRICK with help of big fre@king screw driver . My pickle didn't have enough girth . Lol Thanks for the quick replies .

How do I remove the upper control arm from a body. So far,removed shock, relieved torsion bar.

its a Weber DGV both barrels open (non progressive ) at the same time is that what your asking ?

any offfers wil be considered need these out of the yard !