Search results for query: *

I finally just got my 408 stroker running and was finishing up the timing when I grounded the positive terminal of the coil accidentally when I was trying to tighten the bolt on the distributor. Now it will not even turn over? I looked at the fuses and they seem to be OK.It does have the MSD...

the engine; la 360 .030 over,, kb 107 pistons 15-18 in the hole, mp rods Comp cams 280H cam and prw 1.6 stainless roller rockers Indy heads from Brian /imm he recommended opening to 70cc. head gasket was MR g 1008? .029 thick Doug's headers [/ATTACH] fresh engine...

Everywhere I checked says not available till December , called them direct and they don't know when they will get more. Does anyone know of a place that might have a stash of them? Thanks

Need somone that knows mopar too tune my car. Thanks

At 46-4800rpm? 1st gear she would go to 5300, 2nd gear level at 4700 and 3rd gear would not go past 53-5500 rpm s. Cool 60 degree night. Timing? Now at 15 initial all in at 2500. Thanks in advance for your thoughts. 1971 scamp My build 360 la internally balanced with balanced flex and...

Not sure if y'all are aware and I wanted to share the info but PTC now does transmissions as well! 727 full manual forward pattern transmission Custom TC 2600 stall 3 gallons PTC trans fluid Shipped to NH $ 1400.00 Can't go wrong here. Great service dealt with Kenny one of the owners...

My build 360 la internally balanced Stock crank, 340 hp rods Comp cams 280H Kb 107's NOT zero decked .012 in the hole Prw stainless 1.6 roller rockers Indy heads set up by IMM/ Brian 70cc chambers .29 head gasket Edlebrock air gap intake and 750 cfm carb Miloden pan and mp windage tray...

Gentleman, My first machine shop experience sucked and cost me almost 3 grand . And I question my machinist as I feel I got screwed and he does not know mopar. This is a la360 My question is he internally balanced the parts (twice long story) and charged me twice in order to get my...

I have what was a running drive train from my scamp. 318 engine had a cracked head so I pulled and disassembled for rebuild and ended up with a 360 build. Complete disassembled engine including edlebrock intake , set of 360 smog heads tapped. 318 heads. New eddy 600cfm carb used for 100...

I was wondering if anyone had a summit code they were not going to use I need to get some headers and stuff to finish my build. Thank you in advance for any help. Christopher

Does anyone have a summit code they are not using? I need to get the transmission and springs. Thank you

I just installed my 360 indy/IMM heads with the ARP bolts supplied by Brian . I used the mr g 1121 gasket . No decking of the block or heads. I used the arp lube that came with the bolts and toured in three steps. I was on the 100ft pounds ( and in the final turns) and felt like a couple of the...

I am putting prw stainless rockers on, this pic show the shaft with the mounting bolt through it for a la 360. Does the oil actually get through there or should it be opened up a little?

Gentleman , I have been building a scamp this winter it came with a318 in it and come to find out a cracked head so I decided to build a 360 for it. I got screwed at the machine shop here in Dover nh. I and I thought my builder (as I gave him the info and web site) were building around a...

Howdy folks, I must say I have spent literally 100's of hours reading on this site in the last couple of months as I put together a 1971 scamp. I have gained a wealth of information off this site, so much so that I had to join so I could say thank you and going to be a gold member. It really...