Search results for query: *

I've acquired a nice Weiand tunnel ram for my 273 build and now I need the carbs to go on top of it! Do you have a pair collecting dust? Sell them to me! I'm open to buying two separate ones too if the stars align, of course. Suggestions so far: - Holley 1850-2 600 cfm vacuum secondaries. So...

Does anyone have a decent aftermarket damper for a 273 laying around? I'll be spinning it kinda high so I'm looking for one that's ok for drag racing.

I've bought a dud. I bought a 4-speed in parts along with a couple of 440:s and some other stuff. It turns out most of it was a 2.47:1 ratio 4-speed but the ouput shaft and all the speed gears were from an OD trans. Bummer. Does anyone have an output shaft for a 1966-UP B/E-body, 30 spline...

Looking to buy a set of std bore 440 pistons with wrist pins. Flat top or slight dome, stock compression height and wrist pin diameter, hypereutectic or forged. Don’t need to be new but they’re going in a new build so good shape at least. I’m in Sweden but you’ll be shipping to OK. Block is...

I’m looking for all three planetary sets for a 1989 or so A500 transmission as mine have all got some play in them. They are steel cage sets with four planets. I’m in Sweden but you’ll be shipping to Halifaxhops in PA. Thanks, /Anders

I'm building a 273. Please don't say I should go with a 360 in stead, I won't. I want to be able to rev the engine as high as possible. The stock slugs make this difficult (if I could even find a set of stock 0.030" over stock slugs). When it comes to the stock pistons and rods: what is the...

Hey gurus, I’m putting an OD A833 together with new bearings and all that (kit from Brewer’s). The only snag is that the input shaft is a little corroded. I’m worried it’ll wear the pilot bushing when in neutral and with the clutch engaged. What do you guys think I need to do about it? Would it...

Looking for a 489 case. I’ll take one that’s empty or has an open diff. If you do have one with gears in it, the ratios I’m looking for are 3.55:1 or 3.73:1 but anything will do.

I'm looking for big block heads. Indy, Trick Flow, Mopar, Edelbrock, Bulldog, whatever. They need to breathe rather well so preferably large valves. Iron is OK as long as they have large valves and ports. Only complete heads (minus rockers and shafts) of interest. Preferably with springs for at...

... and I need some guidance. I DON'T need arguments against doing it. I found cheap seat cutting tools from India on eBay and will do the work myself (and post video - whether I fail or not ...). I got a custom kit with six cutter heads so I can do a 3-angle job on all valves, 30, 45 and 60...

I need a rebuild kit for what I believe to be a 73-75 power brake front disc master cylinder (that I got in the Tom&Dee auction back in April). It seems they are out of stock everywhere. The Raybestos article number is MK697 but there may be equivalents. The bore of the M/C is 15/16" and it...

This is cool. A DeLorean that does donuts - on its own. edit: And here's the video: http://youtu.be/WNIDcT0Zdj4

Friends, I bought a used 727 small block dust cover over here but the little "inspection cover" wasn't included. Does anyone by any chance have one laying around? I'd consider buying the whole thing, too. If shipping to Sweden directly is a problem, we can solve that with a US middle...

Oh, mighty FABO, bless me with thy knowledge! I've got a 360 that's currently completely isolated from the chassis. I've got the ignition and starter all wired up for the virgin startup but no ground yet. Wherever I look, there's a gasket. Maybe I'm over thinking this, but where is the best...

My precious 1966 Dart GT Hard Top is apparently missing a piece of sheet metal. The front valance that runs across the front behind the bumper. I'm having a hard time finding a picture of what it looks like. Does anyone know if the valance on other years or models are identical or...

I'm pretty sure the thing on the left is the starter relay and the middle, new-looking is the voltage regulator. But on the right? Is it the hi/low beam relay? /n00b Edit: oops, sorry. Dart '66, V8.

I need a Throttle linkage stud: http://www.summitracing.com/int/parts/hly-20-67/overview/?retaillocation=int I think $24 is steep. Does anyone have one? Shipping to Don in VA 22657 so shipping to Sweden won't be an issue for you. Thanks.

Does anyone have any more detail on the 1970 Dart Poison drives in Narcos? There's not too much info here: http://www.imcdb.org/vehicle_836044-Dodge-Dart-1970.html.

Is this anyone we know? https://www.facebook.com/RoadkillShow/posts/547768238711772:0

I believe the Mopar # to be 2580678 but I am not entirely certain. This is the type of gauge I need: http://bluestarperformance.com/media/catalog/product/cache/1/image/9df78eab33525d08d6e5fb8d27136e95/d/s/dscf2308_2_.jpg The picture is of a FUEL gauge but it is very similar. Shipping...

Hi, Hoping to tap som of the FABO expertise. My '66 Dart GT had a 904 trans but now it has a 727. I still have the filler tube from the 904 but wonder if it will show the correct level reading in the 727. When I insert the level stick, the "fill 1 pint" mark is right where the O-ring...

Hello! First off: I'm a newbie. Never renovated a car before. Sure, I used to fix up old mopeds in my teens. Did plenty of them. From the ground up, bare metal to fresh paint and stickers, overhaul on motor and re-upholstered seat. Since then, not so much. Went to university. Bought an old...

Hi all! Just a few days ago I rolled my '66 Dart GT HT into my garage. I'm so thrilled! The previous owner has done all the work fixing the rust and getting a prepped 360 and 727 and 8-3/4" rear end in place. All I need to do is give it the finishing touch before painting it and then putting...