Search results for query: *

  1. 6

    318 rebuild suggestions

    Ok I have been looking at the service shop manual and it is referencing tools needed to change out the main bearings. Is this tool needed or is there an equivalent? It also talks about changing the camshaft bearings is this nessessary? Again will need a tool for that. On the bearing...
  2. 6

    318 rebuild suggestions

    Ok so first thing I will pull the heads. Are there good youtube videos on how to check for cc. I have never compression checked before. For measuring the gap. I just turn the crank until the piston is at its highest point correct. I am defiantly a little confused. What cam should I...
  3. 6

    318 rebuild suggestions

    From looking at the comp site I should be looking at cam: 20-223-3 Xtreme Energy, XE268H, Great for Street Machines. Also looking at the cam kit K20-223-3
  4. 6

    318 rebuild suggestions

    I will definitely get the rebuild refresher kit, Thanks KrazyKuda. As far as the Cam goes I have seen recommendations for nothing higher than a 268 duration. RustyRatRod, you mention a 340 cam, do you know the specs on that or should I look for something else? I plan on trying to do most...
  5. 6

    1969 Barracuda Restore Project

    Just a few pictures after removing the seats and carpet.
  6. 6

    318 rebuild suggestions

    I went ahead and picked up a used 318 since I am missing numerous pieces to my original 318. It is a 74/75 year block with stock heads #3769973 1.78/1.50 I Do not know if the springs and cam have been changed, it is possible that they have. From looking at the motor it has been rebuilt, but do...
  7. 6

    Pick up a 318 or continue my search for a 360

    Hello, My current project has a tore down non-working (Was torn down 17-18 years ago and never put back together) 318. I was looking for a 360 to put in its place from recommendations here. However, I have found a supposed working 318 with a 904 transmission and converter for $350. The...
  8. 6

    Small to Large Bolt Pattern Conversion

    I currently have the Cragar SS wheels. I plan on keeping these since for now since I am just in the planning stages. The wheel change will be done after I rebuild and have the engine running and the interior is repaired, so it will be while.
  9. 6

    Small to Large Bolt Pattern Conversion

    Or if I keep the bolt pattern I have, what is the largest wheel and tires for street driving that I can put on. I like the larger such as 17 inch rims with the slimmer tires similar to the ones I have on my TA. I am also going to replace the front and rear drums with disc brakes. I to find...
  10. 6

    Small to Large Bolt Pattern Conversion

    I do not know for sure but I believe it is the small 7 1/4. The car is an automatic with the 318 engine ,so I am thinking it is the 7 1/4.
  11. 6

    Small to Large Bolt Pattern Conversion

    Hello Guys I am starting to work on and get involved in Moper (1969 Barracuda Convertible). I have gotten some great advice so far and have more questions. I am assuming my vehicle, which has not been modified (yet) has the small wheel blot pattern. I want to convert to the larger...
  12. 6

    1969 Barracuda Restore Project

    And now since the rain has stopped here is a picture of the left over engine, with all the other pieces in boxes.
  13. 6

    1969 Barracuda Restore Project

    Hello all again, Thanks for the replies and for the direction Kosmic. I definitely want to get it running. My wife coordinated the transportation of the car to get it to me as a surprise. But she wants it in running condition. I definitely want to fully redo the car but it will take years...
  14. 6

    1969 Barracuda Restore Project

    Hello, I have had my Barracuda sitting in a garage for may years (Was previously my late father's). It was last running in the late 1980s and then parked. My dad started the top end tear down and never finished. There was always another car he acquired and took his time. I have move...
Back
Top