Search results for query: *

1969 Dodge Dart - 408 Stroker - Dana 60 - mini tubbed - reverse manual valve body 727 TF built trans with trans brake and Cheetah Shifter - line lock - frame connectors - drive shaft loop - new interior - Paint is good - Car is Solid and Clean - Slicks and Skinnies on Billet Specialties...

Before I pull the trigger on a HEI setup for my SB Dart I wanted to make sure I'm not overlooking something. What am I losing and/or gaining by going HEI over MSD. Thank you.

Hi, I'm looking to do the HEI 1 wire conversion on my stroked 360, 69 Dart. Does anyone know of a reputable brand and model all in one Dizzy that will clear my stock firewall and a standard 14 inch air cleaner? I'd like to get one that had everything right in it so I can eliminate as much as...

...Is the Painless Kit so much more expensive then the EZ Wire kit. I don't see much of a difference between them. Please educate me: https://www.amazon.com/dp/B00NO0Y1AS/?tag=joeychgo-20 https://www.amazon.com/dp/B000VTUAK0/?tag=joeychgo-20

I have a 69 Dart that is currently an automatic that I would like to convert to standard. I'm looking to create a grocery list of everything needed to do the conversion. I know there are kits I can buy to do the whole job in one shot, but they seem to be very expensive. I'm not sure which...

I pulled this out of my 69 Dart. Not sure if it works, but it was an AC car. Make me a reasonable offer and it's yours. $1 Local pick only (Connecticut).

Twin Scoop hood off of my 69 Dart. The only thing missing is the trim that goes along the front. Paint is really nice. Emblems and latches are there. Minor surface rust on bottom side. Asking $300. Pick up in Shelton, CT.

I'm looking to do a complete upgrade on my ignition system. I currently have the Mopar electronic setup in my 69 Dart / 408 LA motor. I'm looking to swap over to MSD. Dizzy, 6AL and Coil. My goal is to get rid of the stock voltage regulator, ballast resistor, and mopar ignition boxes. I...

Swapping over my SB 408 from a MP electronic distributor to MSD setup. My current distributor is mechanical only, when I order my new one should I get the vacuum advance setup or stay mechanical only? There is about $150 price difference. Thanks in advance.

Sorry for the n00b question, but searched and couldn't find a straight answer. Where would be the best place to pull key on power for an electric fan relay on my 69 Dart? I'm using a Spal harness and Fan. Thanks Ken

Hi, Looking to remove the heater blower everything system out of my 69 Dart. How hard it is to do or can it be done without pulling the Dash? no AC Thanks

Hi, I'm looking to convert my 408 Stroker, 69 Dart over to dual electric fans. I know I want spal fans and a harness with good relays. My problem is I can't seem to find the right shroud for my radiator. The Rad was in the car when I bought it and I have no idea of the brand, but looks to be a...

Took my Dart out yesterday the temp outside was about 68 in CT. The car is a 408 stroker with a 727. Once the car got up into the 200-210 area is started to spudder as if it was mis-firing. Once it cooled back down to the 190 area it seems to still be there just not as bad. The cooler it got...

Hi, I'm getting ready to drop the 727 in my 69 Dart and do a stall swap. I'm sure it's pretty straight forward, but with the available resources available I always like to double check the process. Anyone have a basic step by step or any advise for this please? The car has a reverse manual VB...

Anyone here have experience with a Racepak setup? I was kicking around the idea of one over aftermarket gauges, just don't know if it would be worth it compared to the basic Autometer gauges.

Hi, I was told by the prior owner that my Dart has a new gas tank. It looks like it does. My problem is when I try to fill the tank with gas as it gets to the top and gas starts pouring out from under neither from the filler neck side. Then of course as I drive it leaking out. I can't fill the...

Anyone have any experience with these eBay air cleaners? CHROME AIR CLEANER WASHABLE FILTER 360 Mopar plymouth Fits Quadrajet Carburetors | eBay

What is this and what is it for? It was next to my coil with a black wire going into it from one side of the coil.

HI, I pulled this washer fluid pump from my 69 Dart. It wasn't hooked up but the pump seems to work fine when I push on it. asking $35 plus the ride.

Hi, I've searched the forums and though finding a few topics about this I can't seem to find my answer, so please excuse me if this is a repetitive topic. 69 Dart Trunk Mount Battery w/ new 2 gauge wire connected to a secondary post in engine compartment. 100amp 1 wire Tuff Stuff Alternator...

First off I apologize if this has been posted already. I searched and couldn't find my answer. I have these 2 wires coming off of my old alternator. I'm looking to swap to a one wire and I'm looking at this alternator: https://www.summitracing.com/parts/tff-8509rdpsp Can I assume all I...

I originally purchased this neck and this T-Stat for my SB. It came as a kit. Mopar Performance P4286759: Chrome Thermostat Housing Fits All Slant Six, Small-Block, Big-Block & HEMI Engines 1978 & Prior | JEGS Mr Gasket 4367: Hi-Flow Thermostat Chrysler, Dodge | JEGS I drove the car twice and...

I'm looking for a nice throttle cable bracket for my SB 360 LA motor. It's got a Holley 650 (4777) and a Edelbrock Performer intake. I'm looking for either chrome of polished. Trying to not spend a ton of money on one either. SOmething in the middle of the road. This is what I currently have...

I have a Miloden 8 qt. pan on my 360 LA SB motor. I'm looking for a dipstick for it. Thanks

My current Alternator on my car has a 5 inch pulley. I'm looking to swap that out back to a stock size alternator setup. I'm looking for the length of a stock size belt with no power steering. Just crank, waterpump, and alternator pulleys. Also what belt brand is preferred. Any help appreciated.

Hi, Looking to swap my stock alternator brackets out on my small block. Has anyone used any decent quality ones they can recommend? Thanks Ken

Preferable in the Connecticut area.

Anyone know where I can find or have (reasonable priced) made a set of fabricated, tall valve covers to clear roller rockers, but most important I need baffled holes on the fire wall side of both valve covers for dual breathers, as well as a hole up front on either side for oil filling that...

I'm using an aluminum Radiator in my 408 stroker and someone mentioned I should use the orange anti freeze in it rather then the green...Thoughts?

Hi, Looking to swap out the slicks on a Dart I recently purchased. The slicks are 10.5/28.5 -15 on a 15X10 rim with a 3 1/2 offset. The front I am swapping to a 15x4 rim with a 2 1/2 off set. What size tires should I put on these for the street? Thanks Ken