Search results for query: *

Looking to buy a front end rebuild kit for my Barracuda. It has manual steering. Armstrong power steering as my dad used to call it, lol! Been searching around on FABO looking for information on Front End rebuild kits, along with how to tips. Several folks say to use the MOOG K7103 offset...

Mopars At The Park (Tulsa Raceway Park, Tulsa Oklahoma) November 4-5, 2023. Central Oklahoma MOPAR Association

Central Oklahoma MOPAR Association This Saturday October 7, 2023. Joe E. Barnes Park, Midwest City Oklahoma. See "Calendar of Events".

Getting ready to tear down the 340 in the 67 Barracuda and looking for a few pointers. This car most likely won't be run on the track just looking to build a strong street engine. Car is a 4pd setup with 3.23 Sure Grip/489 case. Before I pulled the engine I ran a cold cranking compression test...

Anyone heard of this manufacturer and if the tires are any good? Looking for matched set of white letter tires for my 67 Barracuda in 235/60 R14 for rear and 195/70 R14 or 205/70 R14 for fronts. Couldn't find the 195 or 205 in Cooper Cobras or BFG radial T/A. At least not so far. Cooper folks...

Does anyone know if a 195/70 R14 radial (24.75") is offered in the Cooper Cobra Radial GT line? A 205/70 R14 (25.3") may also be close enough in height. Currently have new 235/60 R14 Cobras' (25.1") on the rear with Wally World Douglas 195/70 R14 on fronts. Put the Wallys on the front to just...

Need help locating a pair of nice argent silver 14" SBP 5.5" width (3.75" BS) rallye wheels without rust pits please.

Were 14" SBP Centerline Auto Drags offered? If so, anyone know what widths and back sets might be available?

Wondering if there is anyone out there running the WV 14x6 SBP (4.00" BS) on the front of one of these cars? Any clearance issues between the rim lip and the upper A-arm or the top of the upper ball joint? The upper ball joints in the car now have a square top side on them that is about...

Anyone know if Coker is the only retailer selling the Specialty Wheels line of mopar rallyes?

Anyone out there have any feedback on the reproduction Mopar Rallyes from these two companies? Quality of finish, fitment to the car, trim ring fit to the wheel and center cap fitting. I'm looking at the 14x6, 14x7 and 14x8 SBP wheels.

Anyone out there have an extra SBP Rallye (4-5/8" BS) lying around? Doesn't have to be a super nice one but not damaged/warped. Wanting to do a mock-up tire to spring clearance check on my 67 Barracuda to see how much tire width I can get in there. Thanks

Couple of questions about new SBP Rallyes and OEM. 1) What width/back set were available from factory? I am looking at possibly 8" for rear with 235/60/14 and possibly 5.5" or 6" on front with possibly 195/70/14 front. 2) Are there any issues with wheel strength, flexing, trim rings coming...

Anyone know if there are any options out there with 5x4 bolt pattern in the American Racing Torque Thrust D style wheels? Looking around for something like these in the chrome/dark grey spoke look for my 67 Barracuda fstbk. My car is 5x4 pattern all the way around with drums. Seeing a lot of...

Anyone ever wonder about costs of shipping and what some of the things may be that affect it, other than fuel prices, handling etc?? Well, here is a funny one. How about the logistics of the route some of your packages go through to get to you. I order a part from a FABO member that started from...

My 67 Barracuda has a 489 case in it with 3.23:1 ratio running 26" tires. Also has 69 A833 A-Body 4 spd. It is some kind of locking diff I think, as when I backed it into my shop after getting it off the trailer from purchase the tires broke loose and left 2 even black marks on the concrete...

Not sure where to post this question, if this isn't the spot. My apologies up front. I was wondering if anyone else has purchased one of the Edelbrock 7576 SB LA intake manifolds recently and found that the 3rd bolt hole from the front passengers side has either been recess ground with a Die...

I am working on gathering parts to rebuild a SB 340 (Bored 0.030"). I am not rolling in the dough but am trying to purchase the best parts that I think I can afford. This is for what I hope to be a pretty good (I realize that what I call pretty good is all relative) but in the 400-425 hp range...

Does anyone have any personal experience good/bad with these clutches? I'm just looking/researching right now for a clutch design that can hold a possible 400 to 435Hp without requiring the Hulks leg thighs/calf's to push the pedal. The horse power is a guestimate at this point on new 340 SB...

Found.

Received new Promaxx 171/65cc heads a few days ago. Promaxx recommended Fel Pro 1213 intake gasket. Measured intake ports on heads a few minutes ago at 1.125" x 2.250". Looking at using a Edlebrock RPM AirGap intake (port: 0.98" x 2.16") on website. Fel Pro 1213 port size is (1.160" x 2.270")...

Just received a new set of aluminum heads for my 340 build, Promaxx 171/65cc heads. Never ran aluminum heads. Anyone have any recommendations for head gasket materials to use or ones to avoid? Appreciate any thoughts. Thanksanks

Looking for a good used Performer RPM Airgap or RPM Airgap intake maifold for a SB 340 build. Set of new Promaxx 171 heads on their way now. Thanks Everyone

Looking for a set of complete aluminum heads, 1.5 RR and Edlebrock Performer RPM intake manifold for a 340. Mine is a November 71 block casting but probably didn't make it to assembly until 72. Original cast iron intake is a 72 and block is blue. Initially looking at running a 0.480/0.480...

Just got my car out of paint shop a few days ago. Interior is all removed right now and want to replace all wiring from front headlights to back before installing new interior. Been seeing a few wiring update kits out there like C510 and American Auto Wire. They look identical in the pictures...

Got a 67 Barracuda Fastback that was original MM1 Turbine Bronze Metallic. Restoring it but would like to lighten the shade of the MM1a little, if possible or go with the 69 T5 code. I think Plymouth may have called the T5 something like Bronze Fire Metallic? Looks like the MM1that was on the...

I am looking for a HURST 4spd (Console) shifter handle for my 67 Barracuda. I think the current shifter is a HURST Indy model? The current handle bolts onto the side of the shifter. Thanks

Looking for a center console for my 67 barracuda 4 spd. New to the Mopar world, so not sure if the center piece from an automatic console can be changed out to work? Please let me know if you have one for sale w/pics. Thanks

Need a driver side front fender. Prefer one in decent shape (not needing patch panels). Would also be interested in a pair (left and right) if someone doesn't want to break a set. Found Fiberglass but would rather go steel. Highest Regards

Started working on repairing sloppy door hinges on my 67 Fastback. I purchased pin/bushing kit for the uppers and what I thought were going to be new OEM hinges for the lowers (Figured new lowers would be best option long term). When I got the lowers I opened the boxes and both hinges had...