Search results for query: *

  1. F

    GMachine Dart - New Wheel Package

    fronts are good, could do an 18x9 up front
  2. F

    Hello from Spring Branch, TX

    http://www.moparmuscleclub-sa.org/
  3. F

    GMachine Dart - New Wheel Package

    Did you roll your rear fenders? My tires rub the sidewall on turns
  4. F

    Almost time to check out for a while

    have you applied for unemployment
  5. F

    Hello from Spring Branch, TX

    Not to far from me, I am in helotes
  6. F

    Ketchme Kopper Dart

    Your the man, thanks for the wheels
  7. F

    Ketchme Kopper Dart

    that is the factory color
  8. F

    Looking at aftermarket gauges what do you use?

    speedhut....i fried one, one was off calibration and the replaced them both, no problem
  9. F

    Ketchme Kopper Dart

    Just put 3.23s in it yesterday and the fr500 wheels...I'll lower the front back down about an inch and a half tomorrow. Runs strong, rides like crap.....the IAC on the EZEFI is all over the place, not sure what that is all about. 13.9 volts with the headlights, fan and fuel pump on
  10. F

    318 with NOS?

    juice it bro, you only live once
  11. F

    Cowl sealed off......

    put a banana in the tailpipe
  12. F

    Great member Inkjunkie

    wow!!! He did that!!! Omg!!!!
  13. F

    Great member Inkjunkie

    inkjunkie is an awesome guy.....i mean really awesomee
  14. F

    8 3/4 Rebuild Guide?

    that yoke tool is cool, I will make one tomorrow....thanks brutha
  15. F

    8 3/4 Rebuild Guide?

    THANKS BRO, I just swapped a suregrip into my diff, never thought I would do that, this link should be in tech articles.
  16. F

    Battery in trunk wire routing.

    mine goes past the right wheel tub inside the trunk, along the right door jamb and between the carpet and heater then tight on the top of the trans tunnel i drilled a hole and put in a grommet, comes right out by the starter. Also i moved my starter relay to the fire wall so the batt, alt and...
  17. F

    Failed........again........

    So why do you get a free pass? There was a person complaining about his job a few weeks ago and everybody gave him crap, younggun2.0 if i remember correctly. http://www.forabodiesonly.com/mopar/showthread.php?t=217430&page=4 he was venting about his job and you replied, "i hear walmart is...
  18. F

    Welder good deal or not

    why did you pass on it
  19. F

    Hazards not blinking when the brakes are on

    I wonder how you learned that as a kid
  20. F

    Failed........again........

    You complain a lot..
  21. F

    Chinese RPM Air Gap??

    Mismatched runners on the one i bought years ago led to fuel, a lot of fuel, getting dumped into the crankcase and the first backfire caused a crankcase explosion the blew the oil cap off so hard it dented the hood
  22. F

    Welder good deal or not

    I have the 210 handler and i dont think I have used it past the #4 setting (1-10) looking back I think something like that would be plenty for a house garage. I say buy it, and get the gas kit for it, you will be surprised at how easy it is to use.
  23. F

    Hazards not blinking when the brakes are on

    just rewired my car from scratch, curious if i did it
  24. F

    Hazards not blinking when the brakes are on

    Well thanks you son of a gun. Is this on all old cars, I dont remember this from my other old cars. How can I fix it?
  25. F

    Hazards not blinking when the brakes are on

    Is this normal?
  26. F

    Alt switched on wire to coil +

    Well senior looks like your right, the instructions i googled when i wired it had the ign sw on and lamp backerds so i was frying the regulator. you have to be careful of the schematic is it showing the plug or the alternator, they are mirrored. i swapped the two wires and i am idling at...
  27. F

    Alt switched on wire to coil +

    Sir I am counting on you
  28. F

    Alt switched on wire to coil +

    So what are the chances of getting two bad alternators in a row, they put both of them on the machine and they failed
  29. F

    Alt switched on wire to coil +

    Sense is supposed to be permanent hot
Back
Top