Search results for query: *

340 Chrysler O heads, 2.02 intakes, nice condition. Sold car I was going to use these for. Located in Crystal Lake Illinois. $350

Looking to see if anyone in the Chicago area has a small block timing cover available. Going on a 1973 340. Would like to have it by the weekend.

Looking to see if anyone in the Chicago area has a shaft mounted valve spring compressor I could use for the weekend. Message me here if you can help me out. Thanks

Unfortunately I need to have them by June 27th. I don’t suppose there’s a way to get them sooner?

Gtx John, your inbox is full. Can you send me some pics?

What were you asking for the shafts? Do you have any pics?

Looking for a set of 273 rocker arm shafts for adjustable rockers with the grooves in them. Must be in decent shape. Message me if you have a set you’d like to sell.

Looking for the shorter dipstick. Should be around 16”

Looking for a factory dipstick for my 340. Don’t need the tube.

Looking for the dodge hood emblem and medallion for a 1965 dart. Doesn’t need to be perfect, just driver quality.

Emptied my inbox. What were you asking for the heads? I don’t necessarily need 273 specific heads, just something to use. I don’t have an intake yet so I can get the one I need.

Looking for a set of small block heads for a 273. Not looking for anything fancy, just something cheap that’ll work, preferably in the Chicago area. I appreciate the help.

Looking for this specific intake from a 1954 331 Chrysler hemi.

Selling a 1971 340. Complete engine minus camshaft and lifters. Block is untouched original in great shape. Has some flash rust in cylinders from sitting but will clean up with a hone. Has 2.02 j heads, forged crank, intake, windage tray, etc. Located in crystal lake, Illinois Asking $1200.

I added a photo of the damaged block. I have a good welder that can repair it if I can get the piece I need. Thanks so much for the help.

Thanks, I appreciate it

Looking for a scrap block that can be completely unusable. Need a piece to repair another block I have. Would be willing to just take the corner of the block I need if possible. Attached is a pic of what I need. Located in crystal lake, Illinois. Thanks.

$800

$950

1971 340, 2.02 valve J heads, forged crank. Has 1973 340 intake and valve covers. Looks to have been rebuilt at one time. Block is .030 over. Passenger side of block corner has been knocked off. I believe it can be repaired. This engine is out of a barracuda or challenger. Located in crystal...

Looking for an inspection cover for a 904 trans. The one I have is bent so need one in good condition. Thanks.

seeing if there’s anyone in the Chicago area that may have a shop or garage I could use to paint my 1965 dart. Trying to avoid spraying in my garage to avoid any problems with the neighbors. Trying to get it done in May or early June. Contact me here and I’ll respond via email. Thanks

Engine sold

1977 440, rebuilt with only break in time. Edelbrock performer intake, 452 heads, mild RV cam, trw L2266 forged pistons. Bought for a project that I sold so have no use for this. Asking $2000 or swap for 40’s-50’s mopar project cars or good running 340. Located in Crystal Lake illinois.

Interested in the fan. Could you get me the measurements for it?

Looking for a nice molding for a 1965 dart 2 door hardtop that goes on top of the passenger side quarter panel. Also need a passenger side outer tail light with reverse lens intact. Could be complete or just the lens.

1977 440, rebuilt with only break in time. Edelbrock performer intake, 452 heads, mild RV cam, trw L2266 forged pistons. Bought for a project that I sold so have no use for this. Asking $2000 or swap for 40’s-50’s mopar project cars or good running 340. Located in Crystal Lake illinois.

If deal falls through, I’ll take it.

pair of 1965 dart bucket seats. Need to be recovered but complete. Started tearing one seat down to put new foam and covers on but found another set ready to go so i have no need for these. $250 Located in crystal lake illinois. Local pick up only.