Search results for query: *

Selling a pair of small ball joint upper control arms from my 1971 Plymouth scamp. Will need ball joints and bushings replaced. Asking $75 shipped in the continental US thanks

Selling the front bench seat from my 1971 Plymouth scamp. Seat is not in the greatest condition and the drivers side hinge point appears to be detached (see pics). Local pickup only, located in Monroe NC, 28112. Asking $150 but open to offers. Thanks

Selling two small bolt pattern wheels. Appear to be 14x5.5. Tires are old but appear to still hold air decently. Asking $100 obo for the pair. Would prefer not to ship these, located in Monroe NC, 28112. Thanks

Selling these small bolt pattern drum brakes, spindles, and upper control arms that came off of my 1971 Plymouth Scamp. Asking $100 obo. Would prefer not to ship these, located near Monroe NC, 28112.

Hey guys, I just pulled the gauge panel out of my 1971 Plymouth scamp so I could see why my speedometer wasn’t working. The cable spins freely and the mechanism on the gauge panel works. Perhaps the cable wasn’t clicked all the way in. Anyway, while the gauge panel is out, I wanted to change...

Hey guys, Has anyone experienced losing brake fluid through your master cylinder reservoir caps? Just installed a new manual brake master cylinder and a front and rear disc brake kit from Dr diff. I notice that my brake fluid is overflowing, I’m not sure if it’s because it’s boiling over or if...

Hey guys, Finishing up the 4wheel disc brake swap on my 71 Plymouth scamp. Not sure if the fittings I have in the late model aluminum master cylinder are correct. I’m using the one pictured below for the rear port, I’ve tightened it a good bit but I swear it seeps a small amount from the...

Hey guys, Working on finishing up the 360 magnum swap in my 1971 Plymouth Scamp. Need to find an air cleaner that fits. Those of you with similar setups; what’re you running for an air cleaner? Thanks

Hey guys, I’m working on finishing up my magnum swap and I’m not quite sure what to do with my throttle cable. The inner braided cable appears to be too long, I was able to make the cable jacket clip into the gas pedal bracket. I’m thinking about maybe cutting the excess braided cable and...

Hey guys, I’m preparing my new wheel and tire package for my 1971 Plymouth scamp. I’ll be running 15x7 cop car wheels on all four corners, 255/60R15 on the rears. I’m unsure of what size tire to run on the front, car has discs brakes on the front and rear. I’m looking for a nice street car...

Hello, I’m looking for two 15x7 BBP 4.25” (or 4.5”) backspace steel cop car wheels for the back of my 1971 Plymouth scamp. I just need two for the rear, I’ll be going with a different width for the front. I’m located in NC near the Charlotte area. Would prefer something relatively local but I’d...

Hey guys, I’ve only got two of these. I need two more for a set of police wheels I’ve got coming. Located near Charlotte NC. Thanks

Hey guys, Need some help identifying which wheels these are. More specifically, their width and backspacing. Haven’t gotten around to dismounting these old tires to measure the wheels. I pulled these off of my 1971 scamp and I’m looking to see what size radials I can replace these old tires...

Hey guys, Looking for shock recommendations for my 1971 Plymouth scamp. Car currently has a 360 magnum, 8.75 rear end and slant 6 torsion bars. Car will primarily be used for street driving and the occasional pass down the 1/4 mile. I’m looking to put a lot of miles on this car as I’d like to...

Hey guys, Working on installing the dr.diff 11.25” rear disc brake kit on my 1971 Plymouth scamp. I’ve got new snap ring style green wheel bearings pressed onto the axles and I’ve got the axles installed into the housing. However, there seems to be a decent amount of in/out movement of the...

Merry Christmas everyone, I’m having some issues with the charging system on my 1971 Plymouth scamp. The car has a 360 magnum and I’m using a Holley terminator computer to control the fuel injection. I’m using a magnum front drive and the alternator from a 360 magnum. When running, the car...

Hey guys, I’m getting around to finishing the fuel system of my 1971 Plymouth Scamp. My new fuel filler neck is not vented and I’m running a new tank like the one pictured. This car is EFI, the pump is mounted outside of the tank. What would be the best way to vent this setup? Could I utilize...

Hello, I’ve got a 1971 Plymouth Scamp that currently has small bolt pattern and all drum brakes. I’m looking to swap the front brakes over to BBP disc brakes from a 1973 and up car. I am looking for everything I need to do this, a complete setup is what I’m after. I am located in North...

Hey guys, Working on finishing up my magnum swap in my 1971 Scamp and I’ve got something I need help with. I am running the magnum serpentine belt setup so I will be using an alternator that came factory on this magnum engine. My battery will be in the trunk instead of under the hood. My...

Looking for a new filler neck for my 1971 Plymouth Scamp. Does anyone know of a company that makes them? thanks

Looking for a few parts for a 360 magnum I’ve got in my 71 Scamp. I’m looking for the following - Non a/c alternator bracket - Timing cover - Crank pulley and harmonic damper from a non a/c engine? (Not sure if the pulleys are different from engines with a/c vs those without) thanks in advance

Reworking the EFI on my 360 magnum. Looking for the factory fuel rail. Appears to have been discontinued. Any help would be greatly appreciated. Thanks

Hey guys, A dear friend of mine passed some time ago, he left behind a lifetime of mopars that he’s obtained over the years. The family has arranged for an auction to be held (currently taking place). The link provided will take you to the website where more details on what is being sold can be...

Hey guys, Does anyone have a carbureted intake manifold for a 360 magnum they’d be willing to sell? thanks

Hey guys, I’ll be picking up my new 60 gallon air compressor soon. I need some ideas about how to run the air lines for it. I’ve got a metal building, thinking about running the lines across the uprights and installing a couple of hose reels, one in the bay with the lift. And the other near the...

Looking for a chemical cabinet to store my chemicals and flammables in my shop. I would prefer something slim, but full height like the one in the picture as I am limited on space, but I may consider a wider one as well. I’m located near Charlotte, North Carolina. thanks

Hey all, I had a metal shop put up a little over a year ago. Here it is about 58 degrees and raining. I’m noticing condensation inside (I figured I would, read about it some a while ago). I’ve always had the intention on insulating my shop, guess I should do it sooner rather than later. As...

For sale One RH grille insert, two LH grille inserts, ok condition . RH insert: 1 stud broken. LH: one has all studs intact, one has one broken stud and one missing stud. LH with all studs also missing little black end piece (see pics) LH and RH set: $165 buyer pays shipping Other LH: $70...

I know it seems odd. But I am in search of a clean 2005 SRT-4 Dodge neon. Good condition, no rust or excessive mods. Need it to be daily driver quality. I am located near Charlotte North Carolina. Willing to travel up to 4 hours one way, or more for the right car. Thanks

Hey all, I’ve got a 1962 dodge lancer with what I believe to be a push button 904 transmission. The car belongs to a friend of mine and they’ve asked me to look at a transmission leak. Last time I worked on this car (been a few years) I remember it having what I thought to be a pan gasket leak...