Search results for query: *

I'm going through a stock 727 valve body and found some corrosion. The aluminum cleaned up nice but the separator plate has some pits and etching after rust removal, I'm thinking that it's going to leak over to other passages. The shuttle valve was also stuck, but that cleaned up nice as well...

What grit stones should I use to hone/touch up the servo bores?

I've installed all new front suspension components and need to know if the strut rods are supposed to be tightened before or after setting the ride height. I have the pivot shafts and strut rods loose at the moment with about 5 turns of preload on the T-bars. Thanks.

Does anyone have a preferred way to bench test the instrument cluster? 68 Dart, I'd like to start by checking the lights and illumination. What power source would be best?

Is there a release tool for the pin connectors on an MSD distributor harness? Thanks.

Anybody have a picture of a 68 Dart glove box latch striker? I need some idea of what I'm looking for. Thanks!

I'm about to make some repairs to a 68 Dart dash wiring harness. Found some great informational threads here on the proper type connectors, so I have ordered those. Question is what type of wiring is best for replicating the OEM dash harness? I have read some threads mentioning TXL, GXL, and...

After a complete tear down I'm putting the front suspension back together. I was planning to install the torsion bars with only the lca's and strut rods in place loosely. No other suspension pieces (uca's, spindles, lower ball joints) are installed as of yet. I've searched a bunch of...

Does anyone make replacement door weatherstrip clips? These are the white plastic clips that hold the weatherstrip to the inner door shell. 1968 Dart, original rubbers strips are nice condition, but many of the clips have broken off.

Will the new style spool mounts/K member work on an older style (68 273, 318, 340) small block?

Can I use the 68 style strut rods on a 73 K frame? Are the Moog K7040 bushings what I need for this strut rod?

I'd like to eliminate the emergency brake on 69 type 11x2-1/2 manual adjust drums. Can I assemble without the e-brake shoe arm and rear drum struts?

Looking for Holley street dominator intake manifold 383 low deck.

I'm ready to start wiring an engine run stand and have a question on the alternator charging circuit. How do I wire the regulator since I'm using just a on/off switch and push button for start? The mopar type key switch and ignition 1, ignition 2 won't be used. Using an old MSD 6AL and blaster...

Transplanting console automatic shifter and linkage in a 68 A-body. Will the bell crank and linkage rods from a 67 B-body work?

1.094 wrist pin. What should the connecting rod small end measure for a press fit application?

Can I use a rod bearing with a dowel hole on a standard rod/cap assembly, or is that going to be trouble? Clevite CB-527HND

So after mock up I need to shorten the valve guides for more retainer to valve stem seal clearance. I have a cutter and arbor from from Comp Cams and my question is should this be used with lube or dry on the stock cast iron guide bosses?

Looking for a set of Schumacher big block Tri-Y headers. PM here, thanks.

Big block Mopar heads with stock factory valves, single spring with dampener. Does anyone have the part numbers for a Comp retainer/lock combination that can replace the factory retainer/locks? I'd like to maintain the same installed height.

So I'm just about to assemble a set of 516 heads that I thoroughly cleaned and lapped the valves on. These will be put away for awhile, so what kind of lube should I assemble with to prevent rust/corrosion on the seats, guides, machined surfaces?

I'm pulling pistons out of a 400. Everything looking great until I remove a rod bearing to inspect the cap. Need some expertise on what is happening here.

Looking for 383 forged crankshaft with good standard/standard journals. No rust, and I'd like to get by with just polishing the journals. Seller must be willing to package and ship. Please PM here. Thanks.

I'm tearing down a 383 with hopes of rebuilding it. First problem is someone has had it apart in the past. It's a stock 4.25 bore but someone used a ridge reamer, well tried to use one anyway. Lots of material removed, so my question is what is the largest over bore that a 383 can go? I will...

Where can I find the deep style brass expansion plugs for a BB cylinder head?

Can anyone recommend a head bolt kit for Edelbrock RPM heads? Hughes, 440 source, and Edelbrock all have them, but I wonder about the large price differences.

Can anyone tell me if the Edelbrock E-Street heads (5090, 5093) have powdered metal valve seats, and how can you tell by looking at the seats? Lots of contradictory statements out there, even from Edelbrock.

Schumacher TQA torque strap kit for 67 & up A-body. PM here, thanks.

70 style horn pad. Dark green, very nice condition. $75 plus shipping. PayPal preferred, PM here if interested.

69 style horn pad. Black, very nice condition. $75 plus shipping. PayPal preferred, PM here if interested.