Search results for query: *

Looking to see if anyone might have a set of TTI headers for the 383 swap into a Abody. If you do please replay. THanks

1972 Dart Swinger 318 with Jheads and other hp parts and 904 transmission. Has new exhaust with Flowmasters. Body is in great shape with only rust being in right rear lower quarter and it being very little. Interior is a 9 out of 10. Front disc brakes are all new. Power booster, master cyl...

Picked up this 72 Dart Swinger this weekend...Has a 318 with 360 J heads.

I just got a 72 Dart Swinger and was looking to hook vacuum lines so heater would swap positions. Have the 2 lines in engine compartment and wondered if anyone might know which to hook to intake? Thanks....

Ok picked up a 1972 Duster today that has all this in it. The seat have just been done and look awesome and console needs Door repaired and shifter works perfect. The car came with column shift and bench seat. I'm kicking around the idea of swapping it back so I might be looking to trade for...

Need some input on a camshaft to go in my 383 that will produce enough vacuum to run my power brakes but still have a rumble to it. looking to be a cruiser and sometimes blow the soot out...lol. Not a all out race car. Engine has 906 heads and torker intake with 600 holley. Its a automatic with...

Like new. 10 miles of driving time on it. Sold the car then sold the engine. New owner is going to msd and did not need the Pertronix. Have the limiters and advance springs that came with it....$225 plus shipping

Looking for the fresh air vent for the drivers side footwell location of a 70's Duster, Demon, Dart Sport and what ever else will fit. Thanks

Anyone running a 750 Demon like these? If so are they any good?

Looking for a 727 Shifter lever.

Anyone running a u-joint on their steering shaft? I swapped a 383 into a 73 Dart Sport and the Slip box (I know there is another name for it..lol) in the shaft is rubbing the exhaust manifold and was thinking about replacing it with a u-joint.

Anyone know where to get a duckbill rear spoiler for a 1973 Dart Sport?

17x9 and 17x 10.5 wheels and tires...Front tires are great... Rear tires hold air but need to be replaced....$600 or might trade on set of rally wheels and tires Had them on a 67 Barracuda

I have a set of Schumacher engine swap mounts to swap a 383-440 into a 67-72 Abody. Also have trans crossmember. Also have a set of mounts to install a 383-440 into a Ebody. Abody mounts have less than 10 miles on them and are like new. Will take $200 for mounts and trans crossmember plus...

On a 383, what type of adapter do you use with aftermarket manual temp gauge that goes into the block?

Anyone running these? I have a set but no instructions with them. Mine have a poly bushing in between the bar running from front to rear.

Installing a Ford 8 inch in 67 Barracuda fastback and measured 7 3/4 to inside wheelwell and 4 Inches to wheel opening lip. Will this wheel work on the rear? Leafsprings are move inboard.

Anyone running a 8 inch Ford rearend with 8 inch wide rims under a 67 Barracuda? What offset are you running?

Looking for a good Autometer 5 inch tach with shiftlight and recall and speedometer. Also be interested in 2 5/8 Autometer oil, temp, amp and gas gauges. Thanks

Looking for 2 aluminum slots 14x5-14x7 with SBP bolt pattern. Thanks

1974 Dodge Dart Swinger Special All original 318 2 barrel carb with 904 automatic trans Power steering Power brakes Ac... Solid floors and trunk Original paint Drive anywhere....Daily driven by me Tagged and insured in my name New tires, shocks, gastank and sending unit Has dent on right front...

Have a Dana 60 with detroit locker, 410 gears, brake shoes, wheel cyl, hold down springs, all bearings and brake drums.... All new with maybe 30 miles on it built by Moser. Axle has the long studs in them. Still under my 67 Barracuda. Asking $1650. Location is Millport Ala.

The 67 Barracuda I bought has a dana 60 with Detroit locker and 4.11 gears all new with less than 30 miles on it. New brakes, hold down kit, wheel cyl and long wheel studs. I will do some trading on a 8 3/4 rearend.

Have a set (4) of these 14 inch hubcaps that were on my 67 Barracuda when I bought it. $250 plus shipping. Located in Millport Ala 35576

Are they all the same on a 6 cyl and V8 car?

I bought these parts to install on my 74 dart but just bought a 67 Barracuda with 383 and going to leave my Dart stock.... I bought this camshaft From B.R.E Demon Its a Crane Hvm 278-2-nc camshaft Its a hyd flat tappet and the specs are 278/290 467/494 lobe sep 114 Rpm range is 2200-6200...

Heading out in the morning to get a 1967 Barracuda fastback 383 clone!!

Half of the dash lights are out on my 74 Dart and I'm going to replace all of them and bulb holders. Anyone know how many bulbs in the dash? Thinking about going with led lights. Anyone running them?

The Dart I just bought has Special under the Swinger emblem. What is the Special package?

How could you tell if one was a original or aftermarket?