Search results for query: *

If it has large ball joints, it is probably the same.

I’m looking for 1973 to 76 upper a arms. Must be for a disc brake car.

What is your price and shipping to Michigan? Also condition Thanks

My stainless on glass got knocked off and bent. It taps on glass and helps seal next to the quarter window.

I have a 67 barracuda that needs a correct wiper arm and refill. There are so many out there. My one has red push button on it. Need another one if it correct. Any thoughts?

I used PPG Shopline round $112.00 a qt and PPG 2021 clear. I don’t know how it will hold up, but it looks very good.

I always hear about someone welding in a spare tire well,but I was thinking about making it deeper to handle a possible 70 series tire. Has anyone ever done this before? Thanks

If If you live in a warm climate. Foil works best with a minimum 1 inch air space. If you have easy access iwould install it 1 inch below your roof decking.. Then I would insulate the ceiling with a foot of fiberglass or blowin. . This would give you the best bang for the buck to stay...

I used a slide hammer to remove dip stick tube. I tapped a bolt to fit, put locktite on it.let it set a week. After 12 slides ,out it popped.

I found a chrome one from Autozone spectre 5721. Says it fits 318;340-360 was to long ,going to cut it and use old dip stick. Haven’t removed old one out ,yet

I wiggled my 318 dip stick tube to pull it out,to replace it. It snapped off.I checked a 273 and the tube length is shorter. Any tips to remove broken tube. Thanks

I’m working on a 67 air conditioned Barracuda. I’m wanting to replace the hoses.What is the correct size?Is the rubber block connector available? Also,some hoses have stripes on them. Any info would be helpful. Thanks

Here is some pictures.Are thrush muffler s any good? Real close to torsion bar.

I have a slightly modified teener,with a fresh dual exhaust system. The muffler shop put thrush mufflers on it. The engine has not been fired up yet. Are they alright for crountry driving? Also how close to the torsion bar should the exaust be? Thanks

Does a dessicant snake have beads that you can change? Would it be better to buy a metal canister? Thanks

Also, how is the pitting? Gordon

Do you still have the hood letters.Are the prongs in good shape and not broken off.gordon

Text me price. Condition and where we can meet if it's not too late

My hinge rusted and a.m. looking for a a nice replacement.It had a piece of plywood with carpet on it.You could lower it down or leave it up.It is located between the rear wheels in the inside of the car. Thanks

I have a used dash pad out of a 67 barracuda that is all cracked. Does it have any value for somebody that repops these dash pads? Thanks

I pulled the steel panel that fits between the rear wheels. it had a piece of heavy craft paper on it.I was thinking I need to insulate it with foil that has a thermal break in it.The foil will radiate the heat back toward the floorboard.The foam sandwiched between the foils will be the thermal...

I changed the panel on my 67 with the panel that has 2 rectangle cut outs as I will be putting duel exhaust on it. It was hard to cut the backup light holes.just take your time.

I was looking at the quarter window felts to install and noticed the curve doesn't match the felts. Do you have to bend them to fit? You would think they would be manufactured correct.

Does anybody have a source fot the pivot arm that is chrome?

I kept wiggling until I had it off .Then i took a drill bit by hand and got the corrosion out of the pocket.thanksw

Should I cut old on off and find another one?

If by some chance I don't get it broke loose.Could I cut the chrome piece off and find another.does it just push on? Thanks