Search results for query: *

Looking for a little input - to read fuel the plug needs cutting , ground strap indicates timing , and some say heat range is indicated by the threads. Here lately I have a hard on for reading plugs. Pics are of the same new plug with 75-100 miles on it. Thanks for your input. -Mike

Bought these 4 or 5 yrs ago from a guy who bought them from Indy 22 years ago. still in the boxes they were shipped in. Have a decent idea what they are but looking for more info. Have a chance of using them. Indy tried but offered no solid info. Anyone have any leads ? Look like new . LA cast...

340 engine removed for repair . We've run it for the last 6 years not knowing too much about it. Solid flat tap cam & lifter. Thought I would learn more about cam but my searches come up empty.

In search of both front side markers - Thanks -Mike

Went to put a thermostat housing on a intake I have and intake uses a 7/16 bolt . Housing I have to put on uses the smaller 3/8 bolts. Need a housing that uses the bigger bolt. Anyone point me in the right direction. Thought they were all the same but I'm wrong again. Thanks -Mike

Internal balanced rotating assembly . Had to replace a single piston and thought I ought to replace everything in that cylinder . Target rod weight - 415 -164. Replacement - 429-166. Acceptable or no. Appreciate your opinions. Thanks -Mike

Fat chance but here goes - Wiseco K0146A100 piston. Thanks all. -Mike K0146A100 WISECO PISTONS DISH STROKER 10.0:1, 4.100 BORE - MOPAR 340 / 360 CHRYSLER SB individual part# is 60146RA100 - passenger side- thanks

SCA- 2- ICR 6123-2124 A connecting rod - checking here first. Can you buy them individually ? Thanks -Mike

looking for premium shoes, hardware kits, & drums - small bolt pattern 10 x 1.75 . Thanks -Mike

Can the pinion seal in a 8 3/4 , 489 case sure-grip be replaced without going any deeper ? Everything else seems good - only complaint is its slinging a little lube making a mess underneath. Thanks. -Mike

chasing my tail looking for these to snug up rod linkage - any leads appreciated. Thanks -Mike

Searching for a good 18'' 7 blade clutch fan - pics & price please - prefer with clutch but without clutch will do. Thanks -Mike

Looking for a good set - Anyone ? Thanks -Mike

Anyone see something needing attention ? install timing set 6-12 dot to dot, degreed cam & had to retard crank gear to get centerline ( 3 degrees), #1 at top, dot on cam gear & "new zero dot" on crank gear line up dot to dot, mock up timing cover and slip damper on enough to catch key and they...

some slow progress & other nonsense - never built an engine before

MRE 1262 from Mancini - bought a few months back - fitting it this past week & surprised to find chain short. Called & they sent another quickly. It arrived & its the same - too short. Called again & they are sending comp kit # 7103. We'll see. Anyone else's too short ? -Mike

Looking for correct cam plate bolts please- Thanks-Mike

Hughes girdle, Milodon 32230 windage tray, Melling M72HV pump, Milodon 18343 pickup in a Milodon 31590 pan, with a 4" stroke & Scat 2-ICR6123-2124A rods. 10lbs of sh-t in a 5 lb bag.

Looking for correct gas cap for early 71 Duster. Thanks -Mike

Are these pumps rebuildable ? Looks like you could if you can find a kit. I've searched with no luck. QFT 30 360QFT .

Searching for an intake edelbrock 7176 OR equivalent - LA engine . Thanks. -Mike

Looking for a single 2.02 and 1.60 valve for a little bowl work . Anyone have any laying on the floor or in a drawer ?

What are the issues with the 190 trick flow heads bolting to TTI headers on a LA engine ?

90* oil filter adaptor wanted - cheaper the better - thanks

Anyone have a pair they didn't use ?

for a '71 Duster driver side front corner of hood. Measures real close if not 9" & letters are about 1/2" tall. 3 studs on backside for mounting. Anyone have one in the toolbox ? Thanks -Mike

1971 Duster in need of LCA with tabs. Thank you -Mike

for '71 Duster Thanks -Mike still looking

Ordered the poly-loc motor mounts & a trans mount from this company this past Tue. - 3/31. Received parts today Sat 4/4. Good email communication - no delay shipping with tracking. This transaction went just as it should have. Satisfied with zero complaint. Some positive feedback for this...

Want to r&r fuel sender in 71 duster without removing tank. New tank in , used old sender because it worked well & very accurate. After install naturally no gauge reading. After checks everything points to sender. Lock ring tool would make it easier to do tank installed. Suggestions on lock ring...