Search results for query: *

price shipped to 22980 see above

1970 440 VIN 0B178675 10/28/69 2536430-5 11-11-HP PULLED FROM A 1970 CUDA six pack rods damper 30 over 10/10 crank stock replacement cam package 906 heads new valves springs retainers rockers shafts hold downs 70 amd valve covers six pack pan pickup 70/71 exhaust manifolds new pulleys alt and...

1969 block and crank block is standard hot tanked pressure tested rust soaked no damage good clean block crank original to the engine just turned 10 10 cast 7,14,69 pan rail ob212337 casting 2780930,340,6

PP63-4350 3B547815 this is the numbers on the pad how do you read them ? thanks

3 housings a body 8.75 2 stock dim 1 48 inch for mini tub application bare housing 300.00 / housing and NEW axles from dr diff 4.5 bolt pattern green bearings 650.00/ housing with used axles and brakes 650.00 /2 489 case suergrips 1/355 and 1/410 750.00 each

new strange 60 rear a body dim 354 gear quick performance axles wilwood disc brakes with park brake never installed 3000.00

lower control arm driver side 1969 dart shipped to va 22980 [found]

stock rebuild what piston is the best choice as far as putting compression at a stock level with x heads

need the two lower pcs only

need info on e body hp manifolds will they work in an a body dart 1973 manifolds if it matters ?

anyone know if the 1969 1970 dart seats are the same as far as frame and fit i know the cover and headrest vary but ?

big block low deck tti headers looking for wire looms valve cover mounted any suggestions to keep wires off the header tubes

looking for a pillar plastic interior trim also one door vent located at rear of door inside thanks

windshield reveal trim clips /purchased the clips from Laysons for the front and rear 68 barracuda fastback the clips for the front are all the same as well as the rear Detroit Metal Tech says there are 7 green clips at the bottom of the windshield that are different from the rest just want to...

side markers flat or curved i see them listed both ways to fit 68 barracuda also need a supplier thanks

plastic door vents

LOOKKING FOR FRONT FENDER INNER SPLASH SHIELDS NEED BOTH THANKS

lower interior door below the door card toward the rear what was the rectangular opening used for and looks like something like a light or bezel is missing on mine ?

any suggestions for dash pad restoration or a supplier for new product

purchased a 68 cuda in pieces the lower front valance has 2 tabs and a center mounting point the ends are a no brainer 2 bolts each side where do the two tabs and center attaching point connect to thanks

1963 COMPLETE ENGINE LESS STARTER AND ALTERNATOR ALL ORIGINAL AIR CLEANER BASES WERE MISPLACED AND REPLACED WITH NEW POSTING FOR A FRIEND STANDARD BORE PM FOR HIS INFO THANKS LOCATION 22980 VA. $18,000.00

came out of a 1968 barracuda 150 mph speedometer /tach/trip meter works /all the needles move freely 450.00 SHIPPED lower 48 also have the lens and metal plate that attaches the bezel to the dash cage that are included with purchase

backing plates for 8.75 or dana rear with strut rods and hardware 100.00 SHIPPED lower 48

license plate mounting bracket front has been blasted some pitting in primer still a solid piece 75.00 SHIPPED

rear seat hinge covers and bracket 65.00 SHIPPED LOWER 48 GOOD CONDITION black

heater control with cables and light good working condition 65.00 SHIPPED lower 48

original pad black no cracks no damage all studs tight 175.00 SHIPPED lower 48 PENDING

need both headlight buckets (galvanized piece that holds and adjusts the headlight ) for a 68 barracuda not sure what else may be the same price and shipping to 22980 thanks

building a 470 low deck to duplicate the engine ar engineering has posted in his tech articles ? why did he use push rod oiling /trick flow says that the 240 heads oil thru the rocker shaft so im using a solid roller from comp and planned on using their roller lifters as well is there pros /cons...

looking for the spool type crossmember a body 727 if it matters in good condition