Search results for query: *

I brought my ‘67 parts car home after more than thirty-years parked in my parents “back 40” (actually 10 acres). I’m gathering all of my spare parts, make it easier on my kids, eventually. I never noticed on this parts car before but the driver’s door has the same door lock knob location as...

I know the engine brackets (not the rubber isolators) have been discussed ad nauseum here but this particular question I couldn’t find. I found a set of 340/360 mounts from a ‘71 Road Runner, they are still bolted to the engine and in the car. I have the isolators, I only need the brackets...

Has anyone found an upper radiator hose, driver’s side rad. intake, that is taller than the stock small block hose before it makes the bend towards the radiator? I need a hose that is taller, and straight, as it rises from the thermostat housing to provide easier access to the front carb’s idle...

Dynabrade 6” Dynorbital-Spirit Random Orbital Sander with sanding discs included, model 21035. I bought this new several years ago and used it on my ‘67 Barracuda when I did the body and paint, that is the only project where I have used it. I haven’t loaned it to anyone. Very good condition...

Does anyone know of a custom decal shop that makes small decals in small quantities? I am looking for a SIX PAK decal for my fenders, with the SIX stacked on top of the PAK in hemi orange but cannot find a place that can do it. Similar to the attached picture. I tried to make my own to...

After having a 727 leak become increasingly large I decided to pull it. I do not see a leak from the vent hole, the perimeter of the pump cover or any cracks. The only place I could see it was leaking was around the TQ hub at the pump seal. The TQ is a Dynamic 9" 3000 above stall, I replaced...

A PST 16:1 manual steering box with less than 500 miles on it, same with the Firm Feel Sector Shaft Support, A Body. I bought these last spring, installed them then removed this winter, they work great, nothing wrong with them. The steering box is solid and feels nice on the road. I had to...

This is a ‘67 A body manual steering, column shift column with shifter and all the linkage. This is correct for a ‘67 but will work in a ‘68 and ‘69. Norms Speed Shop built this two years ago, I put a little under 1,000 miles on it. It is straight, turns and spins great, not a problem with...

Does anyone know the socket size to remove the oil filter plate connector? I am tryin to pull it off while reach around my headers and I do not feel as though my one-inch socket is fitting on it. I cannot get a good feel when trying to fit it and cannot see it. Am I using the wrong socket...

I have a ‘67 Barracuda, I bought a Borgeson box, Saginaw pump, mounting brackets, low profile pressure hose fitting assembly from Peter at Bergman Auto Craft. Talk about a guy with patience, I have bothered that man with so many questions but he has never failed to answer me quickly, great guy...

17 push rods, only 200 miles on them, one is unused as it was a spare. Absolutely nothing wrong with them, I bought different rocker arms and needed slightly shorter rods. These were made by Smith Brothers in June of 2020. They are 5/16 x .083 wall 4130; ball at both ends, no oil holes, 7.875...

Two finned, black wrinkle paint valve covers, PCV valve, and breather cap off of a 273, will fit any LA small block. These are all Mopar, not reproduction. These came on my ‘67 Barracuda. The covers are in great shape, no dents and the fins are not damaged. The breather cap has two very...

New reproduction torque shaft, bushing, torque shaft boot, & formed mounting flange. I never installed these. According to Classic Industries these are for a 66-69 A-body but but I think they will work in any A-body console shift automatic starting in ‘66. I could be wrong. Price is $50...

Holley Street Avenger 670cfm, Holley part number 0-83670. It has between 1,000 and 1,500 miles on it. The only changes I have made to it are jets, discharge nozzle, and power valve. It has electric choke, quick change vacuum secondary spring cap, glass fuel level sights, dual fuel inlets, and...

Selling a complete set of small block PRW Platinum adjustable rockers, shafts, spacers, collars and hold down clamps; everything you need but the bolts. Mike at B3 Racing modified the rocker shafts and made a “geometry correction kit” set of shims for me. The shims are for use with Trick Flow...

I bought this Auto Meter Sport Comp water temp gauge summer of 2021 and never used it, the engine was never run with the gauge installed. It is an analog, electric gauge, half sweep, 2 5/8” diameter face, model 3531. I may have mounted it, may have installed the sending unit but I don’t...

I bought this Hurst Promatic 2 shifter as you see it with a plan to install, then changed plans. It only comes with what you see. It doesn’t look as though it was ever installed, no marks, scratches etc.. other than maybe shelf ware. It moves firmly, has a nice action. If you want the cable...

Two tools made by ARE, sold through Hughes. I used them once, don’t need them again. They don’t look as though ever used. New these are $37 combined, plus shipping. Asking $27 shipped anywhere in the US.

The topic of swapping a 67 to 68 K member, swapping 67 idler arms for a later version etc... has been beaten to death but I did numerous searches on this site and Google but didn't find the answer I want. Has anyone compared a 67 idler arm to a 68 side by side or using some accurate form of...

I am looking for a small block six pack intake manifold, linkage, carbs. Mostly the intake manifold. Thank you.

Maybe someone else has figured this out and already posted but I didn’t find it in a search. I’m sure many of you are like me and don’t want to pay for a reverse lights switch for your console automatic or even the column auto. They cost far too much for what they are and lots of Mopars use...

I used this to remove my torsion bars, worked perfect, even with my headers. This design is very close to the original Mopar torsion bar tool and works much better than the short, no handle version sold by Mancini and others on the Web. I cannot remember who made this but I believe it was a...

I have an almost brand new Resto Ricks pistol grip shifter for A body or early B body automatic console shifters. If you have not seen one of these in person they are very well made and look great once attached to the stock shifter. They work by spring action where you simply push down the...

As my post title crudely states, I am asking if someone can measure, unless you already know, the size of the opening of their four speed console, where the shifter comes through the top plate. I want to install my E body slap tick shifter and it’s shift plate (proper name?) into my console...

For any of you guys that are interested in duplicating paint marks on your car I'm uploading three pictures. I'm replacing my bushings and repainting but not duplicating the assembly paint marks but thought someone else might want to see these. These are on my '67 Barracuda Formula S. It's...

I know this topic has been beat to death but I couldn’t find an answer directly related to what problem I have. I bought some Mancini Raving XHD leaf springs for my ‘67 Barracuda, finally installed them this weekend. When at rest on the wheels the passenger side shackle is at about 85 degrees...

I've read a few posts on people struggling to get the one-piece strut rod bushing installed: using c-clamps, pounding on them etc... Maybe someone already posted this but I thought I would pass it on. I bought a brand new rubber set from Moog, made in the USA surprisingly. I first put some...

I read quite a few posts here and on the B Bodies forum but couldn't find an answer: Do I slide the torsion bar dust boots on the bar, then going from the engine side/front of car, do I slide the torsion bar into position, moving the bar towards the rear of the vehicle? It seems as though it...

I know this has been discussed repeatedly but what I didn't find in any posts during my search was fabricating the correct "top" portion of the mount on my '67 K-frame to use the bolt through '68 idler arm by using the original "bottom" mount currently holding my '67 idler arm. I bought a new...

I have a brand new Edelbrock aluminum head for a small block LA (60779), also comes with a brand new set of valves, seals, shims and locks for the same Edelbrock head. None of these were ever run on an engine. I ruined one head by trying to hog out the push rod holes, bad idea. Instead of...