Search results for query: *

Hey i saw that pic of the small block radiator aluminum and you put a pic of the ford contour dual electric fans fitting on there. I want to go the same route and I just purchased the fan. How did you get the correct wiring/plug connection that is shown in the pick? Did you build it or buy the...

Do you think these iron ram heads can support a cam of this size 250/254. 603/608 ??

I believe hughes stated on the website when these heads were offered is that thry were 179 cc runner and 62 c.c. combustion chamber. Just trying to get actual numbers because I'm just guessing at this point. Trying too see whats the biggest cam I can go to while keeping these heads and actually...

Already tried. he had no numbers for me....wtf

I have a set of hughes iron ram heads on my 408. I have been trying to find out the specs of my heads as far as the combustion chamber and runners cc. Hughes 4676SP was the part number Says They are cnc super st prepped The invoice says they did a racing valve job Cnc chambers 2.02 and 1.620...

Hello I have a small bolt pattern dart with a 8.75 rearend. I switched it to large bolt pattern Moser axles. I bought 10x 2 1/2 backing plates and shoes. They bolted up fine. I purchased Durago #8878 10 inch drums. I put them on and I have alot of rubbing going on. Wear marker of rubbing on the...

Hey guys in the process of putting a new harness in...i was dumb and forgot to take pics for visual reference. I got it pretty much taken care of but I can't find where some of these connections g0

Thank you

Hello. I have a 1970 dart 340. I removed the dash to get it restored and found that the wiring harness is labeled 71 from previous owner. Gauges never worked. I bought a 70 dash harness to correct this, The harnesses seem to be almost exact except for a couple spots. I noticed on the 70 harness...

I had them Redo all my gauges and test them. Fix heater control. Restore the gauge faces with new lettering/numbers. Make sure Speedo working and fix some broken prongs on circuit bored. Along with restoring the front of gauge housing. 1,000 bucks. I did not send in Whole dash. And I bought...

Oh **** really? I'm way off. So voltage limiter is in the fuel gauge? I had instrument specialty redo it all. If thats the case I would assume they put one in and it works.

Hello I'm trying to find a new voltage limitor/regulator. I have a 70 swinger 340 speed car. I just got my dash and gauges redone and dont want to fry my gauges. I can't find a limitor regulator that looks like the one in my car. Mine has 3 prongs close together than 1 more a little lower. For...

Not sure what n51 is? I do not have a build sheet

I can't find those part numbers on it...there is p16219 on the fan and blades say 3870 107 2465

I'm trying to figure out what's the correct fan,on my 70 dart 340 4speed car w/ no AC. I have a 5 blade fan and a 18" fan with 7 blades...

Th Thanks alot

Hello, I have a 1970 dart 340 4spd car. I bought a new wiring harness for it from classic industries for the updated electronic ignition. The car has no ignition module and the 2 connection ballister not the 4 prong one. Runs fine! I have a electronic distributor I'm installing My question...

I already bought that one. That part number is just the rear harness. I need The wiring in between rear harness and tail light housing...the exact wires and bulb sockets that are shown in the pick....cant find them anywhere

I have a 70 340 swinger 4speed. The tailight housing wiring is crap and where the bulbs sit is rusted out. I'm looking for housings with good wiring that plugs into the rear harness! Does anyone know of a place that sells this or can make the new wiring connection? Thanks

I'll do it, anything is a right step. Much alpreciated

No pop or stumble at all or backfire

Ok thank you

Ok I will, I'll just put a new one on along with a fuel pressure gauge. Can't hurt. thanks

And my mph are slower at every distance. The whole time after I launch it feels slow and not pulling or accelerating. Feels like engine is working but car not moving

I checked them they appear to be fine visually but I have not taken them all off to inspect pushrods or lifters

60 ft have best been 1.68. On my best pass slowest 1.92

6 years from revmax

Hello, I'm trying to figure out what's wrong with my dart swinger it has a mild 408 with 727 manual valvebody 4,000 stall 8.75 391. The car ran its best of 11.97 @ 113.95. I ran this pass 3 weeks ago and came back the following and ran 11.97 again, then 2nd pass 12.1 then 3rd 12.50 @ 107 Since...