Search results for query: *

MSD 6AL box thats made in the USA. Comes with a 6k RPM chip. Blaster 2 coil that has no dents/dings. $125 plus shipping from 49285

Ran for a year. Pulled engine to go with an LS...so there is no longer a need for this. Comes with: Stock red cap. Has a hole drilled so you can phase the rotor (I used clear RTV to seal it...runs fine like this). MSD phasable rotor Stock non-phasable rotor Summit racing SUM-G5245 - Gives...

Hello.... Not sure where to start so I'll just list what I have! Mopar 360 LA with Edelbrock Super Victor EFI intake that is controlled by megasquirt (not included). Built this last year and ran it in my jeep wrangler. Its less then 500 miles. I ran a turbo with a 7 psi wastegate spring. It...

Hey there! I have a 88 Jeep wrangler on 42s with a Mopar 360LA that has a turbo. I have ALWAYS fought running hot while running at Silver Lake Sand Dunes in Michigan. It never gets hot at idle or driving down the road or in stop and go (its not a DD so hardly EVER happens). Regardless, it...

Anyone have a timing map for an LA with a single turbo runing 6psi on 93 pump? I have meth injection to keep the intake charge down and to add some fuel. Have a good timing map rite now, just wondering if anyone has one I can compare with and see if I'm way under advance.

Morning, I'm currently putting a turbo on my 360 LA that is in my 88 Jeep Wrangler. The engine always had block huggers that I hated! They cause high under hood temps while out in the sand and on the trails. Plus, they always leak and crack. So, I would like to keep it simple and run stock...

46re with transgo shift kit to convert it to a full manual vb. lockup and overdrive are activated by switches that ground the solenoid. This is in my mopar 360 la powered 88 wrangler on 39.5" tires, with steel beadlock wheels. So very heavy. Was at the sand dunes few weekends ago and...

I believe thats what it is called. You assemble the planets on the shaft with all the thrust washers, and install the C-clip. Flip it all over and have the sun shell on the table, and then you put a feeler gauge between the very bottom sun gear and ensure there is proper play. Well I can't...

Building up my 46re for my jeep. -I have 5 direct clutches going in -Using all 15 springs -Will set clearance of clutches at .060 - .075 (.010 - .015 per clutch) -Get ride of the the wave snap ring and replace with desired thickness flat style -Sonnax billet front cover -Sonnax acumulator (no...

Replaced the blown out flowmasters with Mac flow path. 2-1/2" inlet, and around the same size casing as the flowmaster 40 series. This is on my Jeep Wrangler and I'm finishing up the flanges to weld everything back up. Cannot wait to hear it on the streets!!!! These took about 2 months as they...

Went to pull the harmonic to re seal the timing cover and water pump and find play in the crank. Have not put a dial indicator on it yet but I can feel and see it move so I know it's not in spec. How screwed am I? Looks like cheap torque converter is to blame here.

Never gave this any concern 7 years ago when I did a full rebuild. The port that is located under the forint pump cover has always been sealed off with rtv. Why would this be done...or is this suppose to be done for some trick? Thanks!

Own a 88 Wrangler with a warmed up 360 LA with megasquirt EFI. I had installed a B&M transpak shift kit long ago. Then decided to put a Transgo TF-2 kit in. It always had a 2-3 flare shift and I never gave much thought about it. Ordered a Turbo Action Forward Pattern MVB, heavy duty rear...

There has been some interest in this system that I run on my 360 powered wrangler. I figure I would post what it is and how it has worked for me. Please feel free to ask any questions you may have about this setup. I should be able to answer just about any. This system is 100% tunable. You...

So I have been having issues with my Jeep with a small block 360 LA. I run a megasquirt ECU and while cranking my tach on the computer goes crazy. It will spike past 10k. So, it will not want to start since it thinks it is spinning fast and is requiring more fuel causing it to just flood out...

I am running the edelbrock EFI intake. I bought some alum. fabricated high height valve covers long ago. With the injector boss's I had to grind down the edge of the valve cover to fit that area...i ground to far and there is a hairline crack that has developed over the years. It leaks oil here...

Just got back from Silver lake Sand dunes where my jeep ran 220+ if I were beating on it. Been fighting this heat issue for years. Its a mild built mopar 360 with cast heads, around 10:1 compression, flat top pistons, cam, headers. The water pump is a mopar performance and i think its...

I built a 360 for my 88 wrangler. I was just wondering what I should limit the RPM to? Here are the specs: Stock heads with small pocket porting summitracing block hug headers Dual exhaust with H-pipe Howards Cams http://www.summitracing.com/parts/HRS-712221-08/ 6.1 Roller Rockers...

I had to purchase a set of ( 8 ) pistons as I needed them ASAP for my engine and only needed to use (1) piston. So up for sale are (7). You can purchase a single piston from Jegs or Summit for around $65. $350 they come with the pins. Located in Livonia, MI 48154 I do not frequent...

I bought a MOPAR 360 oil pan for the Magnum block to use on my LA. I went to the dealer and bought this. I forget what I paid as I had got employee pricing as my dad works for Chrysler. I installed the pan and ran it for about a week. The pan does not work for me as I needed a higher capacity...

Installed roller tipped rockers and they shoot a stream of oil out of the oiling holes on the top. This gets past the small baffles and allow it to leak out of my breather on top. Has anyone made a shield to deflect the oil down? I see they make something for the ford and chevy engines but can't...

I installed some roller tipped rocker arms and now when I hold a high RPM you can watch the oil pressure drop. I am using a magnum stock pan as I wanted the one piece pan gasket. I can't seem to find a 8qt pan for the magnum... ? I think that since the oiling on the rockers is better , I just...

360 la, what are good pushrods to use with the crane cams ductile steel adjustable rockers? Hydraulic lifts. length?

Heads are off and at the machine shop getting a great deal of work. 2.02 and 1.60 valves going in, pocket porting. Now I'm looking for a set of good roller adjustable rockers. I do not want to spend $500 for a set though. This engine is installed in my 1988 Wrangler where I drive it like I...

Will the magnum style fit on a LA block? I'm running megasquirt computer management so I'll be controlling the timing with that.

For my 88 jeep wrangler that sees some road driving in the summer. I need it to idle with a fair amount of vacuum. I want it to sound throaty/raspy/mean at idle though. Current cam is a CompCam http://www.summitracing.com/parts/CCA-20-222-3/ 360LA block out of a 78 magnum Heads are out of a 88...

http://www.summitracing.com/parts/EDL-28155/?image=large Has anyone used this for their LA 360? I run a megasquirt ECU with a chevy 350 tbi on my 360. It works but I want better fuel control and better response and POWER! I can't find anything on this intake through searching with google.

Looks like my rear main seal is leaking. The engine has to have less than 2k miles on it as its in my 88' Jeep wrangler. It gets a lot of abuse. While at the dunes it will see 5k RPM quite often. Is it possible due to the higher compression and high RPM that the seal got weak and started...

Has anyone done this themselves? I'd like to change from using a chevy TBI and run multiport injection. I know you can buy the bungs for the injectors from MSD that epoxy in. Looking for a write up or if anyone has done this before.

Do they really improve cooling like they say?...30% My jeep like to idle hot, but as soon as I start to drive 10mph it will start to cool down. Running down the road I don't need my electric fan and it stays around 190ish. Since this is in my jeep I do spend time going very very slow while...