Search results for query: *

? Inquiring minds want to know.?

Looking for clutch recommendations for my 410 Stroker engine. I'm going to use the Quick Time Bell housing, I have a McLeod 130 tooth flywheel and was thinking about the clutch pressure plate package in the picture. Its a 10.5 23 spline package. Any one running one of these clutchs? Thanks! MJK

Ok, I have an unusual question. I'm planning on using a Petronix distributor in my new small block. The oil pump drive shaft bushing is new (MOPAR), the oil pump shaft is brand new (MOPAR). When I install the Petronix distributor it only sits inside the oil pump shaft coupling @.090" That's not...

The oil filter adapter plate gasket set comes with 1 large round fiber gasket for the plate and 2 round gaskets for the 3/4-16 fitting. ( one large cork type and one thin fiber) My after market MOPAR SB engine assemble book shows the rebuilder NOT using the small round gaskets on the fitting. (...

Little by little she's finally starting to come together.

Hello! I just received my short block back from Weston Machine. The cylinder heads won't being installed for a few weeks. What should I coat the cylinder walls with to prevent any rusting. I'm storing the block in my garage which is not heated. The block is doubled wrapped in plastic to keep it...

I need a 360 LA block for a project I'm currently working on. I just found out today that my block has several cracks in the left and right side banks. I will need it shipped if not local. Thanks. Mike

Hello! I've searched the forum but can't seem to find how to determine what size speedo gear to use after a tire and gear change. I"m running a stock A833 4 speed trans, rear tire height it 26.5, and the new gear ratio will be 4.10. How do you determine the correct speedo gear? Thanks! MJK

Hello, I've been searching online and I can't believe how hard it is to find the factory MOPAR engine build specs for a 340 six pack motor. I even looked in my 1970 Chilton manual and they don't even list it! Does anyone have a factory spec sheet for this motor? I'm looking for specifics as far...

I'm sure this was a very expedient way to attach the rear deck lid Barracuda script, but.....Looks like a machine pressed / peen. I found a really super clean deck lid trim panel and I'm torn on removing this.

Hello, I'm looking for the steps to replace the key cylinder for my ignition switch. I'm not seeing anything listed in the factory Plymouth manual. Thanks in advance! Mike K

Is it possible for Admin to retrive it? I posted a few photos the other day and it seemed alot of my photos were duplicated. I tried to delete a photo and deleted My Garage.

Hello! I'm looking for a super clean Barracuda logo for the right side of my trunk lid. NOS would be better! Apparently nobody is reproducing these emblems. Thanks in advance in you can help!

Hello, I have a "knock" in my upper steering column when I turn the wheel to the left. It only knocks when turned left, not right. It certainly feels like the upper bearing has a bad spot on it. So to change the upper bearing, does the entire column have to come out? And if it does I would...

Hello all! My 67 Barracuda is missing the parking brake switch assy. I just found a NOS switch bracket, but I'm not sure how its mounted and what type of switch it takes. Can anyone post some photos of the assembly for me. I think the switch looks like a door jam switch? Thanks in advance for...

Greetings all! I"m not sure if I have an original knob or not. It doesn't lock onto the switch shaft. I really dont want to glue it in place. I"ve searched extensively and it seems no one makes a repro knob. The closest I can find is a 1964 Barracuda knob that comes with a set screw on the knob...

Need some help. I just purchased a repro hood to cowl seal for my 67 Barracuda. I currently don't have a seal on my car. My question is how to install the clips that came with the seal. There is no vendor guidance. I know the pointed side goes into the seal, but it seems like it will pull out...

Hello! I hope someone can please help me!! I"m looking for the parking brake cable clamp that is bolted to the dash support. I've been looking for a long time, I thought I got lucky and found one on ebay, but its for a 1968 and up. Thanks in advance!