Search results for query: *

My sister had a 2018 or 2019 (I forgot the year) and worked flawlessly until during covid lockdowns when microchips were in short supply and it had a check engine light pop up so they took it to the dealer for a warranty check and it turned out to be for the TCU. The van sat at the dealer for...

Got 2 forklifts at work. One late 60s/early 70s toyota and a early 2000s mitsubishi. The toyota is 2 stage and rated for 2000 lbs and it struggles as you get close to that 2000 lb mark. It has dually Pneumatic tires up front and does well in different terrain due to its wide footprint. It is...

It's a frame reinforcement for mounting the z-bar. You can see it in the picture of the orange wheel well on the right hand side. Looks like 2 of the holes are welded to the frame and the top hole has a bolt running through it. On the opposite side of the frame will be where the Z-bar is mounted

May or may not be in a pile of parts that I have but I for sure wouldn't have known what it was for. Thank you!

I've been collecting parts for a few years to 4 speed swap my 360 powered 68 4 door dart. the only sheetmetal you should need is the 4 speed hump. If you want a bench seat then you will want to look for shifter handles specific for mounting with a bench seat. If you want buckets then your...

Its not impossible to have your lifters "drain" overnight or after sitting for an extended period of time although this isn't ideal. Turn on the car and let it run for a minute or two (Only want to circulate the oil a little not warm up the car) and then check again. If the rocker shafts are...

I got one in Long Beach

My brother will be attending some of the MLB spring training games this upcoming weekend in Phoenix. I'm wondering if anyone in the Pheonix area has any door glass for a 1968 2 door post car (could be valiant or dart) Please reach out to me if you have one so that we can coordinate I may or...

Tremec t-5 would break almost immediately behind a 340 but he said it's not that so that's good. TKO is a good trans but it's big, be ready for lots of fab time and cutting out the trans hump/making a new one or spending the $$$ on panels. TKX is a newer trans and it's compact, I believe it...

Which tremec 5 speed? There is more than 1

I'm going to assume that if it won't come up in pictures then it's close enough and youre overthinking it. 1* one way or another probably won't affect anything, you don't plan on cruising at 200mph. These cars were never precise to begin with. The good thing is that each bushing is bolted...

On the output side, I would imagine the U-joints will break long before the output shaft shows any signs of damage.

Shift knob still available?

I'll take it Sending PM

Once you have to narrow an 8.75 it's all the same, whether you want to chop it down to run 15" wide tires inside the wheel wells or if you want to convert an B/C/E body into an A body. Basically you're going to look at that list and cut it down the the specs needed for an A body. Then you're...

Get ready for things to go off track, whenever anyone mentions UTG, it turns into a hate thread rather than a help thread... As for your exhaust, as with anything else, it all has to be balanced. Assuming you're going with a 225, that translates to roughly a 3.6L (close enough) engine which...

I have an edelbrock performer rpm on my 360 and I have a normal aftermarket sized air cleaner and it all fits under the hood. I am happy with the intake

AVS2 650 on my 360 and it works great

No notch?

Everything is worth "something", probably not much if they're just cores. and yes they are rebuildable. I've seen both diy solutions that involve sanding, filling in cracks, bondo over Everything, then paint. Doesn't look factory but doesn't look bad These guys do top notch restorations, a dart...

I agree, they're just scrap now. If I was closer I would pick them up for free as a learning tool before touching my own heads

TQ carbs are a little quirky but once set up right they are pretty great. I would like to add that being an '84, you will likely have a sticker somewhere in the engine compartment with smog info on it that is going to have some baseline numbers for initial timing, and idle rpm. Don't ignore...

the pictures are deceiving,they almost appear to only have a few hairs of clearance but in general I would say that 1/2inch is enough if that is what you see I would suggest to take it slow, maybe drive around the neighborhood and hit a few speed bumps and dips and take it straight home and...

If you were in my part of the country to would snatch that up immediately. The shipping wouldn't be worth it for me across the country. Good luck on the sale

As stated above, make sure everything is installed correctly to make sure you absolutely need to dent it (and where). I had to dent my passenger header a little because at idle my engine shook just enough to contact my tie rod bolt. I marked the area with a sharpie and turned my wheels to give...

I got a set of 4 steelies (rim only) from a 2006 dodge charger for $60 I've seen sets here with old tires thay would work as rollers going for $100-150 from similar cars (charger, 300, magnum) they're 17s and I don't have any clearance issues

I am not sure about a specific FABO meet but any and all mopars are there so there will be members from all the affiliated sites (FBBO, FCBO, FEBO... ETC) Including plenty of a bodies I always try to go but it always falls close to my anniversary so I never know if I'm going to make it until...

Not too long ago I took apart and cleaned my whole electronic dist., mine had a mixture of dirt/oil, and surface rust. I used solvent then went over each part with wd40 and a scotch Brite red pad. Once I felt it was good enough, I cleaned all of it twice with a lint free rag that was wet with...

Just a heads up. I had a neighbor who spent months chasing a tps problem in his toyota so he finally broke down and took it to a dealer and the first thing they did was check the spare tire. It was low... they filled it... problem solved. Not saying this is your issue but it's worth checking

Not sure how the warranty works on the magnaflow products but my dynomax come with a "lifetime" warranty as well. Reading the fine print, I would have had to send it back to summit (where I purchased them many years prior) where they would then send it back to dynomax who would then determine if...