Search results for query: *

$3000 Selling my 66 4 Door Dart. I just don't have the energy. Slant 6 225, 904 Auto Transmission with column shift. Rewired with a 65 harness with a couple of bugs, Have all molding, Dart Letters for the hood, Lower quarter panels to replace rusted parts, new gas tank, filler tube, gas cap...

Will a 65 Dart Non AC Heater fit into a to 66 Dart with AC Heater? Any mods needed to the firewall?

#1 Aside from the obvious instrument panel difference 65 round, 66 retangular, which I can modify, are the harnesses the same? #2 Can I replace the old style Fuse Box with a new universal blade style. I plan on eliminating the Bulkhead connector too. Wire it straight through the firewall.

Found this in my Garage from previous owner. It's an air cleaner nut. It has threads on the underside. Pay for shipping from 92307 and it's yours.

Gas Cap that I bought on this site for my 66 Dart but it's for a later model. Has some minor pitting. $25 $5.00 shipping

I can't, for the life of me, get my fuel filler neck back into the tank. I've heated the grommet, boiled it, lubed it. What else can I do? Unless...the fuel filler neck is the wrong one? Mine is a 2" OD. 1966 Dart 270 4 Door Sedan.

I picked this carb up and it appears to be new. I put in on my Slant 6 but it's the wrong sub model. It wasn't taking in fuel so I took off the top and it really needs a new kit after 50 years of sitting around. $150 + shipping from 92308

I took off my Holley 1920 and found a New-in-box BBS. My question is it seems to be for a 1969 D100. Will it fit my 66 Dart? It's missing the choke pull-off and has a few extra vacuum lines. I imagine that since it's been in a box since 1969 it probably needs a new rebuild kit.

Can some of you experts decode this for me? It's a 66 Dart 270 4Door Sedan with a 225 slant six Vin LH41B65105458

Has anyone used a Holley 1904 on the Slant Six? The fuel bowls are glass and interchange with the 1920. Will the 1904 as a whole work on the Slant? I think it looks cool and allows you to see the float level.

Hey Guys I am reassembling my instrument cluster and my headlight post will not snap in. I shaved down the bezel to allow it to go in further but nothing. It is the same switch and the release button is in the right position. Any ideas?

Almost finished with my steering wheel project. I still have a stubborn gear selector to go as well as my horn. On the underside of the Steering wheel is the copper contact ring with the terminal. My terminal broke off. The part is almost impossible to find so has anyone soldered a male terminal...

From a 66 Dart Automatic on the Column. The 'arrow' broke off of my Gear Shift indicator. Does anyone have one? Also looking for the spring that goes to the Shift lever.

I am rewiring my dash and thought I would take care of the Windshield Wiper Pivots and motor. Pivots did great. I also bought the Pivot Seal Kit to seal out any water in the future. I noticed the Motor was not smooth. In the process of taking it apart make sure the teeth on the gear are not a...

I removed my steering wheel to restore and I noticed the outer hub near the gear indicator rotates about an inch in either direction. My shop manual doesn't indicate a set screw or anything that is supposed to hold it in place. What do my experts think?

I removed my steering wheel to restore and I noticed the outer hub near the gear indicator rotates about an inch in either direction. My shop manual doesn't indicate a set screw or anything that is supposed to hold it in place. What do my experts think?

The wind in our area was so strong that it blew my hood up and off the hinge pin on the driver's side. Upon replacing it I realized there was NO hinge pin. I assume it was spot welded on. How do I replace it and with what? Does the fender have to be removed? Need some advice from you pros.

My 66 Dart 270 Slant 6 non/ac had a single sliding lever for heat. Top lever is Heat/Defrost Bottom is Temp/Warm. I purchased a stock 2 lever model and notices it has 3 cables and the heater has vacuum diaphragms. Can I take off the Diaphragms and just have the cable regulated controls? I don't...

I am after getting my Dart working, then I can restore original parts. I can't see buying an instrument cluster for $200 & gauges. My question: Can I use a cluster to a different Mopar if I wire it correctly? Im thinking of an instrument cluster from a 1999 Dodge Dakota from the wrecking yard...

I must of done something wrong. I am rewiring everything so gauges, lights, accessories and instrumentation are all disconnected. It's battery/Alt/Voltage Regulator/Ignition Switch, coil, Ballast Resistor period. Starts and runs great with no issues. The only problem is it won't turn off until I...

If I follow the MAD amp meter bypass concept, could I use the Red/Black as the power lead for the Fusebox? They are still joined-at the fuse box instead of together.

Will a 64, 65 or 67 Instrument dash bezel fit a 66 Dart?

66 Dart 270 instrument cluster hard to find. Do 67 or 68 fit? What about pre 66 clusters?

Has anyone replaced hood or trunk springs with lift supports? I have a 66 Dodge Dart. Just wondering! It is an after market mod but seems like it would look cool.

I'm looking at schematics and the colors for the bulkhead connector does not line up. Does anyone have a photo or can take one for me. I need a close up of the connector on the firewall side!