Search results for query: *

Thinking about building me a 400bb whid 440 crank,ending up whid 451 cui,the direction whid this build is fuel economi not performance,as this engine orignaly is a low comp engine im shooting for 9.5 ratio,any sugestions on cam pistones intake carb,this is a low budget build so cast crank cast...

I have a issue whid my tranny on the truck bb 727 al stock in trans,when cold it pulls normal in drive from say 1000 rpm but when its wormed up from a stand still i have to rev it up a bit like 1400 rpm and it jumps like a frog when it pops in to gear,any id whats up whit that realy annoying issue

Made me a vacuum pump 12v from a rotary pump i saved from a other prodject,I allso put in the new gages iv done a while ago,nothing on the old cluster workt so I didnt have a choise, was supose to whait until i rappt the hole dach in leather but it is what it is

The angrey litle 318 is back in the old 37,after some dizzy mods it started right up and tomorrow il brake in the cam,pickt up a mp dizzy via an ad but the seller wasnt shore if it was for a bb or la to bad its for a rb but I turned all the crap inside the right way,rb rund back wards,and it...

Been fidling whid the timing on my 400bb now im at 18° initial and 42° total no vacuum it has a prutty stout cam i dont knowe the specs but it sounds helty and yes its a low comp engine iv decided to stop at this point,no pinging and stady at 180°f when crusing,any body gone fader than 42

Hi i have problem whid lack of vaccum on my dodge wild cam and the problem that follows so I made a 12v vac pump from a generator mounted pump,made a adapter for the axle to a 12v motor but I dont want it to run the hole time onley when vaccum drops below 15 cant figure out what pressure switch...

Hi anybody have some info on panhard mounting,got some bump steer on my dodge 68 truck and a panhard in the front cant hurt,the question is where to put it,conecting axle to frame is a given but is it supose to be parall whid the axle,have some space in front of the axle but its prutty...

I have a problem i newer had to do whid before its a 98 honda civic aerodeck 1.5,it runs grate but whid the termostate in the engine theres no heat in the cab and if I remove it iv got all the heat i need,iv flucht the hole system and the waterpump is new as the termostate,no coolent is...

All buttend up at last its ready to put back in the old 37 newley refrect sens last sommers dicaster new comp h268 set on 105°centerline,new bearings rings honed polist crank oilpump max ported heads small chamber bigger valves back cut,five angle seats roller rockers that lined up whid no...

Hi where can i bye a not to expensive higher gear for my dodge truck its got 4:10 now and its a bit on the lowe side im running high rear tires but its not enough,the rear axel is a full floater and I Wonder if has the same gears as a lets say b body whid a dana 60.....

Anybody used these typ locks first time fore me,realy cheep and made from alu gona try them out on the truck im modifing the tip of the hood and cant use the stock lock payd 20$ whid shipping

Hi you all where can a buy offset crank keys for my 318 im assembelin the hopt up sb for my rod and whant to centerline the cam i have the old style crank sprocket non adj and I cant find any on line i knowe that macini use to have them but not any more

Thinking of making a sun wisor for my dodge d200 -68 iv tried to find some pics on the interwebb but no luck anybody here made one,found a pic on one that i like I think its on a chevy

Im pulling my hair on desiding how and what to do whid the front end on my 68 d200 all the pics on the interwebb is whid front bumper but i want to make a rool pan like i did in the back whid 2 driving lights like the 70 cuda kinda, but cant get it right in my head what to do whid the part under...

Hi anybody used a for ex chevy sb electric water pump and made a new backing plate been looking at this before and now im gona see it true a el pump for a mopar sb is like 500 dollar here in Sweden but i can bye one for a sb chevy or ford for 170 dollar big diference just wundering if some body...

Have some 308 heads that im gona put on my rebuilt 318 they are ported and al the valve job is done in a shop but something is of whid the valves i think that the intake valve is the ones that came whid the heads and the ex valves is from a 360 head whid bigger diameter than stock but the hight...

Hi im rebuilding and performing my 318 and stombeld over a new set of prw rockers as on the picture newer used this brand before and wonder if some one here has used them before i payd 240 dollar from a shop here in Sweden pros and cons

Hi any pinstripers on the forum im just a nube been striping for a few mounths and im just loven it realy nice pleace post your pinns

As soon as the back end of the truck is done im jumping on the front brakes im from the old scool so no pre fab conv kits not on my watch a friend gave me a brake system from a newer corvette calipers and discs so im gona use the big front calipers made from alu and realy light and dont worry im...

Trying to find any picture on the old way of covering the radioator in the winter to get engine temp up faster iv seen thees things a long time ago on old traktors thay are made from standing sheet metal strips its the mecaniks to Open and close id like to duplicate for my dodge truck it takes a...

At last the big frees is coming whid -30°celciuc iv been looking forward to this for mounths now there is a reason i live in the far north of sweden coold winter and hot summers

Hi you all im pulling my hair on finding a dicent cam for my street engine ..... Specs: 318 std bore comp 9:1 ported 302 heads bigger ex valves roller rockers match ported mid rice intake eddy 750 msd 6al blaster coil 1 3/4 block huggers dual 2.5 ex stock 904 a500 4.10 rear all Street no race...

Hi maby a stupid question but can you use a hyd flat tap cam and lock the lifters or run whid solid lifters if you go whid adj rockers iv onley used roller cams in my race car as long as i can remeber but now im building a 318 Street engine or do i have to go all mec even the cam

Found cracks in the 318 la roller block around the head bolt holes in the left side i guess its doned or can it be fixt anybody tryed to repair it the crackes is running down to the water jackets

Hi you all took the 318 apart today and the new cam comp cam 268 is flat on one lobe the lifter is grounded out like i newer seen before i onley have like 100km on the engine when i blow a head gasket anybody made a warranty claim aginst comp cam iv been building and rebuilding mopar sb sens the...

Hi anybody knowe if all stock pistons for the 318 is the same comp height regardles of whitch year it was made

Hi i posted a question on a other forum but i give up the replies was not what i was looking for so il try here im lowering my truck d200 68 anybody here that have rasied the hole engine-trany pac im bagging it and the pan is hiting the front axel its like 5" clearens in the trany tunnel and...

Im building a new 318 for my rod and im gona bye some heads from a company here in Sweden but they are made in china they are eddy copys ish im ordering emty heads and bying valves and springs from known brand made in usa got a friend whid a head shop and he is gona do the work whid 5 angle...

Hi anybody having any op about proform dizzy kits bout a new one here in Sweden and it has workt fine until tonight parkt thé car coming from a shopping trip and put the items in the house and went out to move the truck stone dead no spark is these ecu just crap or what i turned it of and now...

Painted and asembeld the cluster today made it from scrap 2mm sheet metal and 4mm roundbar made a clock for the glove box lid from an old speedometer not finisht some pinstripe on the clock bottom then asebly il do that tomorow some sheep instruments from ebay not real Smiths