Search results for query: *

My original part broke one of the small hold down tabs off recently. I'm looking for a bezel that is in good shape, before I try to repair the one I have. Thanks!

Last summer when I first drove my Cuda after a pretty extensive restoration, one day my gauges seemed to be acting funny. I discovered that the temp sender wire and the alternator wire got too hot and melted their insulation together right where they lay on top of the passengers side valve...

I’ve got 15 x 7 cragars with 245/60/15 tires currently on the rear of a 69 Cuda. I’m wondering if a 15 x 8 with 275/60/15 tire will fit without spacers? Stock leaf springs.

I'm putting my hood mounted turn indicators on my '69 Cuda and notice that they no longer get their ground connection through the sheet metal like they did before I restored the car. These indicators just have a single signal wire that runs through the hood channels back to the firewall near the...

I've been restoring my '69 M code Cuda and was just wondering about something on the car. It has 'functional' hood scoops! The small 'Cuda hood scoops on this car are open in the front, rather than closed off, and there are rectangular holes cut in the hood accordingly. Inside the hood...

I need to replace that pesky o-ring next to the tail shaft. Can the tail shaft be removed while tranny is installed in a 69 Barracuda? It looks like most bolts are accessible. Thanks for the help.

Any suggestions on getting a pesky caliper cross over line to stop leaking? The seat isn’t in the best shape. Does anyone know of a source for the seat itself? I’ve used a small copper washer I made, but I just can’t get it to stop leaking. Thanks for the help!

I’m doing a basic stock restoration on my 69 Cuda, and am having some electrical issues I’m unsure of. I did the Mad Max (or whatever) modification that bypasses the bulkhead connectors and disconnects the amp gauge in the dash. I used the recommended wire gauge, the two fusible links, and...

I'm in the process of a simple refresh of my 440 engine. Original 70K miles, ran like a top, but it needed gaskets, seals and paint, along with a valve job and some manifold repairs, which I'm about finished with. My question is if it's necessary to pre-oil this engine, even though the bottom...

'69 Barracuda fastback; How does the outside stainless trim piece for the rear quarter windows come off? Also, how do I remove the large painted quarter interior molding? I've removed these three screws, dome light cover, etc. and I still can't see how it comes off. Do I have to remove the...

I own one of the '69 440 'Cuda fastbacks. Mine came with the also rare 'Slickback' vinyl top option in the 'pearl white' color. I believe it is the only M-code car built with this vinyl top. As I'm restoring the car, I will need to replace the vinyl and am looking for some help locating that...

I own one of the '69 440 'Cuda fastbacks. Mine came with the also rare 'Slickback' vinyl top option in the 'pearl white' color. I believe it is the only M-code car built with this vinyl top. As I'm restoring the car, I will need to replace the vinyl and am looking for some help locating that...

I've got one of the '69 440 Cudas, as you can probably tell by my handle. I'm currently doing a 'cosmetic' restoration of the car, and have always been curious where others have found their build sheets in the past. Places I've looked; under carpet, behind bucket seat backs, above glove box...

Has anyone done their own reconditioning of their steering gear box? It looks like a guy could do this himself, preserving his original case, etc., and also quicken the steering ratio at the same time. That is if this is legitimate; Firmfeel Mopar Suspension and Steering Has anyone had any...

Hello. I'm new to this forum, but not to my '69 'Cuda that I bought from my brother in 1973! Anyway, I'm in the process of freshening up the interior, and need to paint some 'new' kick panels as close to the original red paint as I can get. Any suggestions on vinyl paint for this? Thanks, Doug