Search results for query: *

Nice little Barracuda, has a later model 318 magnum that had only 26k miles on it, 4 speed, 3:91 suregrip. Power steering, ralleye wheels. Runs really strong. Body is in great shape, very solid floor pans and trunk. Paint is a 20 footer. Interior in good shape. Needs carpet. Glass is all good...

nice Cuda. 65, 318 magnum engine with low miles. 8 3/4. 489 case rearend. Body in excellent condition with very minimal rust. Bumpers could use a rechrome. Was factory under coated and underside is in excellent condition. Paint is about a 7. Couple of place on the top where clearcoat is peeling...

ive got an 833 4 spd.. My question is: are there different lengths of the front bearing retainer. I know there are different diameters, but is the lengths of the snout, that the throw out bearing rides on, different. I’m having problems with the throwout bearing on a 3 finger clutch. One of...

4 nice 13” aluminum slots with new tires. Sbp , lugnuts included. $325 plus shipping OBO. Open to reasonable offers.

1 formula s hubcap. $25 plus shipping. I’m told it’s a 13” cap.

hey guys. I have a 65 cuda that I put a 318 magnum in. What oil pan do I need to clear the center link.

i put a 2000 model 318 magnum in my 65 cuda. Bought a flywheel and bellhousing off FABO. Have a vibration in the engine. At 3000 rpms it vibrates pretty bad. How can I tell if I have the wrong flywheel. Are there numbers on the flywheel. I’ve heard that 318 magnums are externally balanced.

looking for 2 14x7 rally wheels. Sbp. Not concerned about shape as long as they aren’t bent. Reasonable price, shipped.

8 3/4 open rearend. Took it out of a 65 cuda and put in a 489 3.91 posi. $125 plus shipping. OBO . Needs to go

v8 emblems

ive got a 273 , 64 model out of a barracuda. It was a 2 barrell with a 904 automatic. I took it all apart to check for and problems cause it had been sitting for awhile. Crank, block and pistons all look to be in good shape. Block has slight ring groove at top. Not bad at all. Heads need hot...

has anyone ever switched from regular electronic distributor to a one wire electronic distributor. What do I get into on removing the module, ballast and wiring mess. I’m doing this on a 65 Barracuda, sb v8 that was changed over to regular electronic distributor with ecm. Thanks in advance. Rick

ive got a 65 cuda and I’m doing a v8 swap. Putting in a 2001 318 magnum. Everything’s is going good till I get to the oil pan. Bought one from summit, it don’t fit. Hits on the oil pump and won’t go down. Tried a 64 273 pan. It fits all but the rear seal on the bearing cap. It likes about 3/4 “...

im putting a 318 magnum in my 65 cuda. Is there a difference in motor mounts. The mounts I took off the 273 don’t seem to work on the drivers side of the motor. What do I need. Thanks, Rick

I’m told it fits a 65 B Body. I bought it for my Barracuda and it’s too small. Very good shape. Chrome is real nice. $45 plus shipping.

is there 2 different sizes of yokes for an 833 and an 833OD transmission.

good shape , all pins intact. Original. $45 shipped to you

good Hurst 4 speed shifter. No handle or shift levers or rods. Just the shifter. $80 shipped in the lower 48.

8 3/4 hogs head, 3.23 open. 741 case. $225 OBO. Open for offers or trades

i have a nice 833 OD 4 speed. Aluminum case. Was in my 65 cuda. Changing it over to regular 833. Works great and smooth. Also have a bellhousing, flywheel and clutch for a slant six. Also have a good slant six hooked up to it all right now. Would take $850 OBO for the whole setup. $400 OBO for...

looking for a horn button for a 64 barracuda Woodgrain wheel. Not sure what years would fit.

looking for a horn button for 64 Cuda, Woodgrain wheel

anybody got a 833 4 speed in good shape. Not looking for OD. Preferably close ratio.

can anyone tell me which 833 4 speed I have with the numbers in this pic ? Thanks

Can anyone tell me if a water pump on a 318 spins the opposite direction if it has a serpentine belt. I had a big block Chevy with serpentine belt and it spun differently than one with regular pulleys.

im looking for a flywheel, clutch and bellhousing for a 318. Swapping

standard steering box out of my 65 Cuda. Changed it to power steering. $50 plus the ride. The steering column is posted in another thread.

Good column out of my 65 Cuda. It is for standard ( non power ) steering. $60 plus the ride

nice Grant steering wheel. All mounting hardware with it. $50 plus shipping

looking for a descent horn button for a 65 Barracuda, wood grain steering wheel.