Search results for query: *

Anyone out there have a good solution to get shoulder harnesses in a 68 barracuda convertible? Had a close call a while back when someone pulled out in front of me. It’s got me jumpy.

I purchased an alternator that the local auto parts store's website assured me would fit my car. Unfortunately it doesn't seem to....but it almost fits. Comparing it to the alternator I took out, it seems to have some extra features (circled) in the housing that rub up against the engine block...

I just got my gauges working. Oil pressure seems to be reading a bit low. (See attached) I figure it should be in the middle somewhere. Before I go troubleshooting further, can anyone tell me what tick mark their oil pressure gauge reads normally?

Having trouble finding the lens that goes near the floor on a rear interior panel for a 68 barracuda/dart. see well-drawn arrow below.

I need the two small pieces that go on either end of the trim, as well as at least four studs to mount them. I found this on Ebay, but its missing the driver side small piece. A good picture of what I need though. Mopar Convertible Top Well Opening Chrome Trim Barracuda 1967-68 A Body | eBay

Looking for rear interior side panels for a 1968 barracuda. Classic industries has some, but they are apparently for a Dart. Its a good visual aid for what I'm looking for, however. 1967-1969 All Makes All Models Parts | MP14061 | 1967-69 Barracuda / Dart Convertible Primer Rear Side Panels |...

I recently replaced the carb with a more correct carter 2 barrel (the one that was on there was not original, the one I bought looks right but didn't come with a tag) and am having some issues where the engine will lose power if I quickly press the gas. The faster I press the gas, the more...

I have a 68 barracuda that I know no history on, but am pretty sure has had numerous changes/pseudo restoration. I was rebuilding the carb and screwed it up, so I'm looking to replace it, but its not obvious to me which carb is correct/will fit, and the pictures of parts I'm seeing online don't...

If I mount a proportioning valve prior to the brake warning switch/distribution block, will that cause the switch to stay on. The switch works on pressure difference, so I assume mounting the value prior to that block will cause issues. I can also mount the proportioning value after the block...

I bought a W153 front disc brake conversion kit from SSBC. I was putting it together and found the bolts that hold the steering knuckle to the adapter plate and spindle rub on the rotor. I talked to their tech support and they told me that the bolts have to go in from the outside. I don't...

I have purchased an SSB-W153 front brake conversion kit, and was busy reading the instructions, and found out I need a different master cylinder and a proportioning valve. After digging into it appears to me that someone before me has already replaced the master cylinder with the one needed...

Does anyone know where I can get mounting hardware for a 1968 barracuda with a 318, as shown in the service manual. Plate,bolt, unut, and maybe clamp. I found the insulator assy at rock auto.

ive been driving around my car around town, just a few miles. When I get back, the grease caps feel pretty hot. Doesn’t seem right to me, but both fronts are doing it, from what I can tell the (drum) brakes aren’t on (they spin about as freely even if I loosen them until the adjuster wheel...

I'm not experienced driving old cars, so I have no frame of reference. My 68 barracuda sort of needs constant adjustment when driving down the road. If I go over bumps, steering can shift, enough that I'm nervous going over 35mph or so in anticipation of some bump. I've put new control arms...

I think I'm going to need a replacement front wheel hub. Anyone know where I can get one? 68 barracuda 10" drum brakes. I was replacing wheel studs, pushed them out, pushed new ones back in. put the tire on and a couple of them started spinning, the teeth had stripped out. Now I gotta get...

On my 68 barracuda, I have all left had thread wheel lug studs. A couple are broken off so I want to replace them. I'm wondering if they are supposed to be LH. It seems odd. On the passenger side, they are all right hand threads. As an aside, anyone got advice on pushing wheel lug studs in?

I've been looking all over for upper control arms to replace the upper control arms in my 68 barracuda (drum brakes). Its been a disaster. I tried the QA1 tubular control arms. The first set broke almost immediately, which I sent back. The replacement set didn't fit, they hit the bracket...