Search results for query: *

Im still in the process of rounding up parts for my 66 B-Cuda project, which entrails changing from a /6 to a 78 360, withan A904, both from same car.. Not going to use the colum shifter, cause I will be using headers. My question is ....... "what after market floor shifter kit have you used...

I have a nice, clean, AM Radio from my 66 B-Cuda (the one in my avatar) works real good. I am not using it. Wires are intact, and it comes with the rear mounting bracket, and the face plate. $165.00 plus actual shipping. I am in S. E. Wisconsin. PM with all corespondence. Dave

I have a nice clean 66 Dart Radio, for sale. This came out of my 66 Dart. I am not using it. It works good, wires are intact. The speaker wire connectors have been changed by some one, not a big deal. Comes with mounting face plate and bracket for the back. $165.00 plus actual shipping. I am in...

Hello Everyone I am looking for two (2) nice B-Cuda fender fish. Looking for 2 that are decent looking, with no pits on chrome. The mounting pins can be broke off, as I will not use them. If you have a set of fender fish (left,and right) that you don't need at at a resonable price send me a PM...

Looking for a set of Barracuda Fender fish. They are PN 2785321, and 2785320 left and right sides. The tabs can be broken off as i don't need them. This is for a project, not going on a b-Cuda. What do you have Thanks Dave

I redid a few electronic distributors, so I built a stand for them, so they don't lay around and get banged up. Black paint was all I had. Dave

What years were these in use, and in what vehicle. I just dug one out of my stash. I didn't know they had such a thing. Its a Mopar distributor Dave

Can any one tell me what the numbers on the SB vacuum advance canister arm mean. See attached pics. I'm rebuilding a couple of distributors, and am curios. These numbers are not visible when the distributor is assembled. I'm geussing they are something to do with vacuum. Dave

Any one know where I can obtain the internal bushings and washers that are inside a SB dizzy,??? I was redoing one today and the plastic busing on the bottom of the dizzy cracked off, when I was putting it back together. Use to be you could get them, but I've had no luck finding any. Thanks Dave

I have a pair of Kelsey-hayes calipers for sale. I have done the hard part of removing the old pistons. They are cleaned up, and ready for new pistons, or you can use them for cores. $75.00 plus shipping from Wisconsin. Coversations welcome. Dave

I have a Performer 318-360 Edlebrock Manifold for sale its in good shape all threads good.The center divider has been machined down some. $150.00 plus shipping from Wisconsin. Dave

I have a new RED 64 B-Cuda headliner priced for quick sale. Don't know what brand it is but it is new. It comes with extra fabric for the visors. May fit 65, and 66 B-Cudas also. $45.00 plus shipping from Wisconsin. Conversations welcome. Dave

For sale is a pair of 67 Commando Valve Covers. They are clean and ready to use. They have been black powder coated. They have 2 very small dents, but they are under the inside baffles. They have the original plug wire inserts, and nice aluminum fins. They can be yours for $150.00, plus shipping...

I have for sale a 68 Plymouth Factory Severvice Manual. It is a reprint. It is in real good shape. A couple pages are loose but thats all. $ 30.00 plus shipping. Conversations welcome. Dave

I have for sale an exceptional pair of 1967 SB Comando Valve Covers. They have been black rinckle powder coated. They have the original plug wire looms. The aluminum finns are in nice shape. Their are 2 small gliches in them, as noted in the pics. One is a small dent, the other a paint glitch...

Anyone know if the Belvedere Mopar Happening, usually at the Boone County Fair Grounds, in Illinois, is on this year in mid July. I havn't been able to find any listing for it, On the Chicagoland Mopar Sight. Thanks Dave

I have a reprint 1968 Plymouth Factory Service manual for sale. It in real good shape. I sold my 68 many moons ago. Front cover is retaped on as it just came off today when I was looking at it. Book is clean, hardly used. $60.00 plus shipping. It will be sent by USPS printed matter which takes...

I have looked all over, and can't find the dimentions for the A Body 8 1/4 rear end. I need the flange to flange, and backing plate to backing plate widths. I have seen it on the sight but it is being hard to find. I am going to look at one this week end, and don't want to buy the wrong one...

I am in need of a slant 6 1 bbl carb. The fuel inlet in mine is stripped out. The brass fitting can be pulled out with your fingers. I can't move the car the way it is, and my wife is pissed, its in her spot. I actually just need the bootom half with the inlet and fuel bowl. The engine is a...

I have for sale a set of small block cam parts, Used very little in a 75 360 back in the 90s. Complete set of valve springs. Complete set of hyd lifters, will be marked as to what cyl they came from. These have the snap ring, and not the wire clip. Double roller timing chain set, I believe its...

I have for sale a new in packaging "Allstar Performance" cam brg removal/install tool # 96470. It is listed for small block Chevy, but it might work on other engines. It is brand new, never used. $42.00, shipped. Thanks Dave

OK. So Im puting my J heads back together, and have a dump question. Im using Felpro # SS70014 OE style valve stem seals. My question is, "how does the intake seal fit the valve guide" (its stock, not machined down),??? Does it get pushed down on the guide,??? or does it just get...

How does this cam seem for a mild 360 build. Just got it. Its an Elgin cam kit, came with lifters, and springs. $212.00 shipped on Amazon. It will be used with .030 over, Wiseco flat tops, with one row of valve reliefs. Just doing a mild buid rebuild of a 1975 360, for my 66 B-Cuda, to wake it...

Well I finished seating all the new valves in my heads. I lapped each one, to its own cylinder, and checked them for leakage with the cly head full of water, No leaks. So then I deburred all the casting flash on the inside, and outside of the heads. Then I cleaned the heads up real good, and...

Well ive gone ole school on these J heads. Doing the valve seats with my ole Craftsman crank ing valve grinder, and permatex valve grinding compound. I must say this cleans the valve seat up quite fast, I was surprised. Got new valves on order from Rock Auto, then I'm going to seat each new...

Polished the crank for my 360 build today. Got tired of it rolling around when i tried to polish it, so i made a stand. works good. no more rolling around. Try it, you'l like it. Dave

1 (1970s) Auto Meter 2 3/8th Temp Gage. bezel is rough, and lower mounting bracket is missing, otherwise its all there. One set of minnie gages, no wiring, bulb mounting is messed up, otherwise never used. Small gages are less than 2 inches in diameter. What you see is what you get. $35.00...

I have for sale a 68-69 gage panel with 150 MPH speedometer , and vacuum gage. speedo gage will need a new speedo face decal. All the pins on back are good, and tight, printed circuit is good. Vac gage works, and speedo moves good. I don't have the trip odometer reset knob. EDIT...

I have for sale an old Chiltons Tune up book. THese are long out of print. It is in rough shape. Some how it got oil stained. it is all theier , and ledgible. some of the corners are torn off the last pages. $20.00 plus shipping. I taped it on front , and back years ago. PM if interested Dave

I'm looking for a small block aluminum oil filter adopter for my 360. Don't want a cast iron one. Let me know what you have, by PM. Thanks Dave