Search results for query: *

  • Users: Mrpatel
  • Content: Threads
  • Order by date
  1. Mrpatel

    Removable skid plate for k frame

    I thought someone may be able to use the idea or modify it for their own use. My oil pan hangs down below the k frame and I wanted some protection. In the photos I used square tubing and plate and welded grade 8 bolts inline with the 2 holes from the factory on the k frame. This allow the k...
  2. Mrpatel

    Accusump installed on B motor

    I thought I would share a few pics for future reference for other members. I used Riv nuts in the inner fender well to mount the band clamps and Aeroquip fittings. It’s a 2 quart system. Note; I have a Victor intake on and I have the rear of the hood kicked up about half an inch. Andrew
  3. Mrpatel

    Single pole switch for Canton Accusump

    Can anyone tell me what type of switch will work for the valve on the accusump? 12v / 9w as shown in the photo. Thanks Andrew
  4. Mrpatel

    [WANTED] Hemi hood scoop

    looking for a bolt on Hemi hood scoop, stinger / AAR preferred. Thanks
  5. Mrpatel

    $20.00 Summit bucks

    i have $20.00 that expire at the end of this month that someone can use. ZT87042874 Andrew
  6. Mrpatel

    Stock big block radiator cooling 700hp

    Figured I would ask the question one last time before dropping $800 on a Griffin Radiator. My last motor was a 511 aluminum headed 10.55 : 1 with 20 degrees initial timing and 34 degrees total, with zero issues with cooling with my stock rad. Motor was built by muscle motors who claimed it was...
  7. Mrpatel

    1968 Dart steering column length Grew

    look for some ideas on what happened to my column length. I went to put the column back in today and it’s a good 2”-3” longer at the u-joint. Are these solid steel shaft or does the center slide in. If you look at the picture, you can see where the bearing sat. Can I tap this is with a mallet...
  8. Mrpatel

    [FOR SALE] new Dynamic converter

    I have one brand new in the box, uninstalled 9 1/2" 3200 converter as shown in the attached photos with specs. 727 transmission $600.00 plus shipping. Thanks Andrew
  9. Mrpatel

    Schumacher transmission mounts

    i just received my new transmission mount from Schumacher and it is 1/2” taller than the original stock one. Wondering if this is going to cause any issues for me with clearances? Thanks Andrew
  10. Mrpatel

    Torque converter runout

    What are your thoughts on checking runout and what would be considered acceptable?
  11. Mrpatel

    Edelbrock RPM head casting flaw

    New Engine loaded on the engine run in stand and ready to install the headers. We pressurized the system and a small leak appeared in the corner of #2 exhaust port. We poked at it and a much larger cavity appeared. I purchased these new 10 years ago, so I am doubtful Edelbrock will do anything...
  12. Mrpatel

    Rear shock length and options for Caltracs

    Looking for ideas on shocks or plate modifications for my 68 Dart. My springs have been moved in board and I purchased the -1 mono leafs. I am 14 3/4” from eye to eye. I purchased QA1 TD901 and they are too long. I am considering purchasing the TS709 or welding up a new lower mounting point 2...
  13. Mrpatel

    -1 Caltrac mono leaf

    who is using these on their A Body with the springs moved inboard? What length of shock are you using? Thanks
  14. Mrpatel

    Free shipping on Caltracs

    I see Jegs just started carrying Calvert Racing products with free shipping over $100. Chicago Connection also sells their products with free shipping. Getting tired of paying shipping from the likes of Mancini. Andrew
  15. Mrpatel

    68 BB K Frame reinforcement pics needed

    i have my k frame out and have seen several posts on this topic, but it was still unclear what areas need to be reinforced on an A body B.B. with manual steering. Has someone taken photos that they could share? Thanks in advance. Andrew
  16. Mrpatel

    Choosing the right Caltrac mono leaf spring

    Looking for suggestions on the corrrect mono leaf spring for my car and what determines the height? Car details 1968 Dart GTS BB 700 HP 727 / foot brake 325 50 15 rear tire 8 3/4 rear. Not sure the exact weight of the car. Thanks for looking Andrew
  17. Mrpatel

    Homemade front torque boxes

    made a set of these up over the weekend. Turned out nice. I dimpled the holes for xtra strength. $14 in steel. Andrew
  18. Mrpatel

    [FOR SALE] 2 1/2" Pypes X Pipe with 3" straight section for dumps and O2 sensor bung

    $200 CDN can be shipped. I had this on my 68 big block dart installed to a set of 1 3/4" primary TTI headers. I made the 3" section to flow straight through using electric cut outs. X pipe is from Pypes. O2 sensor bung was for my AFR gauge. Slight staining, but will clean up. Thanks for looking...
  19. Mrpatel

    727 Transmission and 600+ hp on the street

    Any reconditions on what is required for a 727 on the street? I currently have a 68 transmission for my big block with a trans go 2 kit in it. Any chance of it surviving? Andrew
  20. Mrpatel

    3" exhaust reducing down to 2 1/2" after x-pipe

    Will I loose any significant power by running a 3" exhaust and reducing it to 2 1/2" after the x-pipe? I will be making over 600hp and it will be difficult to run 3" all the way out to the back. I thought I saw something that mentioned that the first 4' matters most. Thanks Andrew
  21. Mrpatel

    [FOR SALE] TTI headers for Mopar TTI383440-134C1

    Used 1 3/4 TTI Nickel plated headers. $500.00 CDN. Can be picked up in Niagara Ontario or possibly Oakville if needed. Ad is also on kijiji. Thanks for the ad and looking. Andrew
  22. Mrpatel

    Victor intake on a B motor and stock hood

    does anyone have a victor intake on a low deck and can still close the stock hood? Thanks Andrew
  23. Mrpatel

    Solid roller cam wiped out

    Big Red ate another cam shaft, this time a solid roller. Wore .063" off of #3 exhaust lobe. Looks like the roller tips on the lifters seized. Down for awhile..... Comp .631, not sure what the lifters are. Should I consider a hydraulic roller for the street? Andrew
  24. Mrpatel

    Cylinder Head Porting in Southern Ontario area

    Looking to possibly have my Edelbrock RPM Intake and Heads ported over the winter. Any suggestions? Thanks Andrew
  25. Mrpatel

    Shipping advice from CA to NY

    I just bought a classic motocross bike just outside of LA, does anyone know of a reputable shipping company? Thanks Andrew
  26. Mrpatel

    [FOR SALE] For Sale 67-69 Southern Dart Hood

    I have a mint stock hood that I was going to put a HEMI Scoop on. No luck finding a scoop, so its up for sale. $100.00 CDN. Pick up only in Niagara. I can post photos. PM if interested, Thanks you. Andrew.
  27. Mrpatel

    For Sale Mint stock hood 67-69 Dart.

    Fore Sale. I have a light green southern stock Flat Hood that I bought with the intentions of putting a Hemi Scoop on. Not sure what to do with it. Open to offers, must pick up in Niagara On. PM if you are interested.
  28. Mrpatel

    pretty cool and much appreciated

    Last week a friend of mine was getting his exhaust fixed and ran into a guy with a 69 swinger there. They started talking about my 68 GTS and passed some photos back and forth on the phone and gave me call. Long story short during the conversation I suggested he have a look at this site if he...
  29. Mrpatel

    Almost new Holly 850 DP

    Mechanical Secondaries, Holley Model #4781. Bought new from Summit last year, has less than 30 hours on it. e-mail me at andrew.calver@goodrich.com if interested. Item located in Niagara Ontario. $375.00 CDN plus shipping. I also have a 50cc for the carb that I would include for $25.00. Thanks...
Back
Top