Search results for query: *

I ordered the wrong one needed non AC. Ck invoice Pic for info Papal accepted Norwalk, Ca Thanks FABO GARY

Thanks for the summit codes @GTX JOHN i really appreciate your help and friendship over the years since we met. Cant wait to see you this sat at the winternationals. Good luck and Thank you again. Gary

Sixty eight dart battery in the trunk three sixty small block street strip car rebuilding from the ground up, Installing a painless 10127 harness kit. I have been a member for quite a while And have read multiple posts on this installation. I am actually following.@crackedback Wiring diagram...

Looking for a one wire alt. For my 360 Thanks FABO

Thank you John and son so much for the awesome hospitality To me and my son Yesterday at the Winternationals. Hanging out with you guys and showing us the ropes all while your running around getting ready for race after race since you were winning race after race and down to 4 cars today...

360 around 500HP i was thinking on installing solid motor mounts question do you guys use solids on both sides or just the driver side. thanks for your answers in advance.

Both units were removed my sons 68 dart when It was put on Jack's in 2016 the steering gear was rebuilt in 2015 as you can see by the scribe writing on the input shaft housing Buy a reputable rebuilder here in Los Angeles. Not sure about the pump except that it has no leaks. the steering...

I recently picked up a manual box from a 63 valiant at a pick your part yard. Its in really good shape but sounded a little dry but absolutely no play . For the money i saved im thinking about putting bearings and seals in it . 1st question is firm feel the only co. That sales a kit for our...

I have the chance to pick up a steering gear really inexpensive probably just use it for a mock up eventually want to get to 16 to 1 PST Does anyone know If a 63 valiant steering gear will fit in a 68 Dart. Thanks in advance Gary

Small block trans Needs to be in complete rebuild able condition. Will be at the fall fling or willing to drive a ways to pick up . Gary

I bought these s.b rockers from A fabo member since I bought them I've gone a different direction on my build just trying to recoup what I paid for them i did not use them this is how they came from the other member, I am not sure the ratio. The shafts look fairly new and some of the rockers...

Complete running engine ( have video upon reqiest) started street strip build in 16 in 18 i started the engine it fired right up . Good running but taking up space. 300.00 obo. Pick up only unless you want to pay the freight. Pm me with questions. Also have wp pulley and alt brackets. Thanks...

Back story , I bought this car in 2012 as a daily driver for my son he drove it for a few years bought a new car then in 2016 we started taking it apart and building a street strip car out of it. The car came with Is a slant 6 automatic automatic didn't really think anything about it till last...

Looking for a single groove pulley for a 70 and later sb la engine with aluminum wp. Gary

Just wondering If my motor mounts are in properly picture on my FSM is a little scratchy So while my rotating assembly is at the balancer I decided to do a oil pen K frame mockup to find out if there was Clarence and like a 100 posts I read on this issue I am going to have to cut either the K...

Excuse my ignorance but can someone tell me the start and end dates of the early A's. Thank you. Gary

My wifes dd is a 2003 suburban. We bought a 1996 four winns 20 ft sport boat in 06, and going to the river is about 300 miles. Towing the boat is a dream with the burb. So last year the wife and kids ( adult kids ) was complaining about the ride (not towing ) and as i had never replaced the...

68 dart 270 hard top looking for pass side trim only Thanks Gary

Bought the poly bushings and greaseable shafts, it didnt come with grease can someone tell me what kind your using ? Thanks in advance. Gary

68 dart 360 i need just the driver side bracket Thx Gary

Motor runs strong good front tires brand new rear tires brand new carburetor brand new aftermarket electronic Ignition. Front disk brakes on a wrecked front beam that goes with it lots of extra parts . I can send you a list if you're Intrested. 2000.00 OBO Thanks for the add FABO.

I'm doing a 4 link , 360 , auto , in my 68 dart. I still have the /6 and trans and front end in the car. I would like to get a guesstimate of where my instant center is going to be before i finish the rear end . My question to you 68 dart 360 sb owners is what frt tire size you have and a...

So i Was wondering what recommendations you guys had for what I already have going on here Would like to know your opinions on rear end gears transmission And torque converter, Carburetor size, rocker arms and push rods (i was thinking on going with hughes and doing the custom p rods since i...

Hi guys the set is for my 741 w 10 spline im asking for a used set do to budget restraints. Thanks Gary

Getting Ready to paint my 4 link bars should I remove the mill scale or leave it . Curious to what you guys think thanks Gary

So I'm setting up my 741SG This was a used case I bought from the Spring fling I'm sure somebody had already replace these gears they have a 1995 stamp on them so I removed the old bearing It has the .091 Spacer under the bearing and I am using the Gear set I wish I could Put a lower gear...

These buckets were in my 68 dart 270 model when i bought it. Did the 270 mod come with buckets or a bench and are these actually mopar seats ? Thanks in advance

As you can see in the pics my chassis bracket is at a 90. My bottom link (as per C.E instructions) is 1 deg front to rear down . It Doesn't exactly say 1ﾟ it just says pointing down from front to rear. And my Links are 20"center to center exactly so my question is why is my Axle bracket at...

I ordered and received my 4 link kit from jegs a couple of weeks ago, 1st complaint , the shipping box was ripped which i know ( since i work for i guess ill just say it UPS ) is not all the shippers fault But if you don't package the parts correctly and tight the parts will fly around inside...

I'm sure this Has been answered before but I'm new to the forum . I'm shortening and 8 3/4 rear end for my dart And putting in green style bearings I have the center section completely apart rebuilding it do I leave the button in or take it out thanks in advance for your answers