Search results for query: *

I noticed when I put the emergency brake on, the pin that holds the bracket on was part way out. I pushed the pin back in though the bracket. What goes on the end of the pin to keep it from sliding out? This is on my 73 Scamp.

I have had nitrous in my bottle for 6 or 7 years. It's almost full. Is there a time limit on nitrous?

I bought new hi and lo horns. I only have one in the car now. Where does the 2nd horn mount? I see the wire for the 2nd horn but I don't see any mounting holes.

I'm running a power shot 125 on my 340 4 speed. I normaly shift at 6500. When using the nitrous do you shift at the same rpm's?

2 New 15 x 8 Weld ProStar rims, 4 1/2 bolt pattern with 4 1/2 back spacing. I just bolted them on and they were not the right back space I needed. Includes center caps and valve stems. $550 shipped in the lower 48 states . Location Mount Morris NY 14510. Money order only.

I have a Summit cross flow radiator which is stamped as a Northern radiator. I have had this for several years. Since I bought this most of the caps I tried leaked right between the cap and rad neck. I did have a NAPA cap that seemed to work but not any more. What could be causing this problem...

The cap is an MSD for their billet dist. What type of drill bit would I need to drill the cap? I have bits for metal but I don't know if these would work. Fred B

How do you change the bulb on the dash light reverse indicator under the dash? Fred B

What are the torque specs for the bolts that hold the shaft to the pinion yoke? Thanks. Fred B

Does anybody run nitrous with a 4 speed? Was wondering if you change the take off RPM. When I run normally I take off between 5500 to 6000 rpm's. I installed a Powershot so it will be 125 shot on take off. Would I lower the starting RPM's? I never ran nitrous before so this will be a learning...

I have a Carter mechanical pump M6270. On my fuel pressure gauge it used to read 7 1/2. Now it reads up to 9 1/2 to 10. I have another Carter pump and switched them. Still the same. It's not pushing the needles off their seat. Idles with no problems. Is my gauge on it's way out? It's quite a few...

What does everybody use for thread sealer? I have used the tape sealer on the long bolt that goes through the bottom alternator bracket, water pump and timing housing. I've already done this twice and it's still leaking. I replaced the old rusty bolt with a new one and I can't get it to seal...

How often should you change the oil in the rear end? Fred B

How often should you replace the PCV valve? Is it still good as long as it rattles when you shake it? Fred B

How often should these be greased? I put less then 3K a year. Fred B

I would like to thank Mrmopartech for the step by step instructions to find my electrical problem. Very good teacher. Thanks again. Fred B

I went to start my car and the battery was low and wouldn't turn the engine over. Battery was checked and is good. Somebody told me that there is probably a short draining the battery. They told me to take 1 cable off the battery and hook the test light clip to the cable and the point of the...

Ok here we go again. If I check the voltage at the fuse box I get 10.3 with ignition key on accessory. With off I get 12.4. With the engine running I get 14.2. What could be causing this? Fred B

Will the gas gauge work without this? Fred B

Got to meet Dennis Gage at the show in Olcott NY. Got to get a picture of him and me in front of my car. He seems to be a decent guy. Fred B

What is a good brand that is reasonably priced mutimeter? I'm looking for a new one mine bit the dust. Fred B

Well since I got the ignition fixed now I have something else. When I put the headlights on my radio shuts off then comes back on. What would cause this? Also sometimes the lights pulse but not all the time. I think maybe it's time for new wire harness. Fred B

Mine is leaking and I need to change it. I put one in about 5-6 years ago. I remember it was hard to get the filler neck to slide into the grommet. Is there any type of lube that would make this easier? Thanks. Fred B

What do you torque the long bolt and nut to. Fred B

Well I finally found out why my car wasn't starting. I checked the ignition 2 wire and there was power to it. I thought WTH. But when I put a volt meter on it and cranked it over the volts dropped to 7. MSD told me to put a toggle switch on. I really don't want a toggle switch. What would cause...

Well I thought I had my no spark problem fixed. Found loose wire and fixed that. Started no problem. That was toward the end of summer. Well now same problem. No spark at plugs. My MSD ignition tests good. I pulled the coil wire and placed it close to metal surface. When I turn the key it turns...

http://www.youtube.com/watch?feature=player_detailpage&v=Pizty9fLdn4 Fred B

On my Scamp, when I go to start the car with my key, it won't start. There is no spark. But....if I put the key on, and use a jumper wire to start it with the solenoid on the fender well, it fires right up. And if I shut it off with the key, it will start right back up with the key several...

My gas gauge quit working. What do I check to find out the problem? Thanks for any help. Fred B

I'm replacing the brake shoes and drums. The Dana 60 I have in my Dart is a '69. The wheel cylinders are original. They aren't leaking and work great. But being that they are that old would you replace them or if it isn't broke don't fix it? Thanx for your opinions. Fred B