Search results for query: *

Pending

Bump

Looking for a passenger side mirror that matches the remote driver's side. Driver quality preferred.

PM sent

I'm changing the wiring harness in my 67 Barracuda to a M&H that is modified for electronic ignition to take advantage of a dual field alternator and the newer style voltage regulator. I was surprised to see the harness is wired for a dual ballast resistor rather than the single. I'm changing to...

I'll take 30 for either gauge.

Unfortunately, I'm not sure if they will work in a magnum block.

I only see one.

Fastback. I edited my posting.

150.00

450 anyone? That's roughly half price.

40.00

I believe this is the heavy duty brake light switch. Bought it for my car before realizing I had the other one. Box has tape on it. 25.00 + 5.00 Shipping

Came with a rotating assembly from CNC, but were never used. 5M1266A ACL Aluglide Main Bearings- Std. Size CB481P Clevite 77 P Series Rod Bearings- Std. Size 50.00 + 12.00 shipping

Two sets of kickdown linkage: Bottom right is the stock setup from my 67 Barracuda 2bbl. It cleaned up nice and is mostly complete 50.00 + 10.00 shipping Upper left is 273 Commando. Bought from a reputable member here, but didn't use 50.00 + 10.00 shipping- SOLD

Unused with a little shelf wear. These came with my 24385 Hotchkis springs. 20.00 + 10.00 priority shipping

Bought it, but ended up not needing it. 35.00 from Mancini, you can have mine for 20 plus 7.00 shipping g.

Very nice and clean 1970-72 340 harmonic balancer. Sheet metal ring on rear is mint! 50.00 plus 12.00 flat rate shipping

Auto Meter 5721 Phantom Mechanical Oil Pressure Gauge, 2.3125 in. - Installed, but never run; I went with an electric gauge instead. Comes with both the stock nylon and brass lines. 40 + 8.00 shipping Auto Meter 5715 Phantom Electric Fuel Level Gauge - Installed, but only run for a short time...

I'll take 500 for the set

Instructions state application is 67-72 a body. I bought this a couple years ago, but ended up using a QA1 bar instead. All the hardware is present, but I think I may have swapped the spacer tubes with the QA1 pieces. As always, shipping is an issue, so I'll pay half of it. Working on a box...

Sale pending. You'd be 4th in line.

Made in USA. New components, not rebuilt. Single groove pulley, includes the ground wire if you're converting from the older style alternator. I had it mounted up and ran for a few minutes to test it, but I ended up with a nice date correct round back and used that instead. 100 plus shipping...

18.11 USPS

Needs cleaned up, has some black paint on it. Mounting ears look solid. There appears to be a little bit of brazing material in the bottom of the exhaust ports. Not sure why, there aren't any cracks anywhere, but the job looks professional. $150 plus shipping

For small block. P5249706, dated 4/98. 25 plus 9.00 shipping

New from Mancini. They have some shelf wear from sitting for a while. 35.00 plus 12.00 shipping.

Model A67LA. New, I didn't even take them out of the bubble wrap. 179 from Schumacher, I'll take 140 plus 15.00 shipping.

Both new in the box. Part of a rotating assembly by CNC motorsports. Pistons weigh between 679 and 681 grams with the pins. 575 obo and 25 shipping.

New M&H 67 Barracuda rear harness. I used one of their front harnesses and the quality was amazing. Asking 170 plus 15.00 shipping in a USPS medium flat rate box.