Search results for query: *

I recently acquired another 66 Dart GT with auto center console. The front buckets are missing. This includes the mounts/tracks. I suspect these parts are not unique to just the 66 Dart. What other years and model of Mopar would be the same? Thanks

What product(s) to use for seam sealing around doors and deck lids where the skin wraps around to the core and for where the quarter meets the rockers? And the rain gutters. Thanks

Picking this up tomorrow. Not sure where I plan on going with it since mine is still on rotisserie. The die cast chrome pieces are better than mine. Slant six GT. Original seats are all gone. Better assessment once it is home and decide future project or part it out

Just pay USPS flat rate shipping, so kind of FREE These are agreeably rough. Came with the grill I got from NM from a 270 model. Have a soft blasted look. Maybe from our southwest dust storms. But if you want to try your hand at hammering them out….

One is okay the other fell out in pieces. Laysons said they didn’t have them. Not sure of official part name and would think it was used on multiple years and modes. This plastic bearing goes on both ends of the hollow shaft that the pedal pivots on when attached to the interior firewall part...

When setting ride height, how much vertical travel should I allow for, for a street fun car. Car is already stripped so cannot just measure oem axle to snubber. Putting in a 9” with QA1 coil over rear suspension. Want it low but safe and tires not hitting my tubs. 2 inches?

Dropped from car summer of 2022. Was driving it till then. No noise. 10” brakes 2.93 gears $700? OBO. Pick at in zip 85142 AZ

Has anyone with a torsion bar eliminated suspension (HDK etc) cut out the torsion bar opening housings, reinforced the frame crossmember with a three inch tube to run exhaust through it? Pros…cons? Just kind of occurred to me. More clearance.

Obviously do not want to ship it but can post locally and for face to race sale. I drove this car around and it was fine. Surely needs some new rubber parts. 1966 Dart GT 273 V8 manual steering. All complete.

Not sure of official name for this part so not doing well on searches for replacement. Since there is little repo metal for a 66 was the same one used on 67+? This the passenger side. Otherwise off to “Wanted” section…. Thanks

I think this an 8 3/4” but not expert enough. Casting number is 8 3/4 right?

This is a hardtop car so no B pillar to make it easier. Has anyone added a retractable three poi t like on new cars? How would I proceed? The car is stripped and on the rotisserie.

66 A body. Mini tubbed and spring relocate QA1 coil over rear suspension It seems I can just about buy all new 9” Ford for the cost 8 3/4 and rebuild. But either way I go, should the rear end be left at 52 or go narrower? Buy wheel tire combo first and decide from there? Never done this...

I have been reading a lot trans talk. I came here since the early As are a bit unique. Car is a center console 904 auto. IF I went a different route on this car and wanted 927, I understand it will fit other than the pinch weld at the mouth of the tunnel will need addressing. Will the same...

I think that the correct method for this issue is to locate a rear quarter (left/driver side) “half tail light can” and section it in. If anyone has a parts car and could part with it. A few spot welds on top and cut it out. Something like the arrows. Thank you

Could not stop. Had a for sale sign on it at Ruthroff and Silverbell. It used be listed on CL for Yuma but no more. I won’t be down there again for few weeks to get more info.

Ready to put the 66 Dart GT hardtop on the rotisserie. I will not be cutting and replacing any floor etc. A lower rear wheel arch is all the metal work needed. So the question is do I need to brace the door openings and cross brace? Or will it rigid enough.

Ran a search on Action Crash but found nothing 1963-1966 Dodge Dart Quarter Panel - Action Crash GMK211069064R - Right - Passenger Side - PartsGeek.com

I searched but… Anyone done flush fit glass like modern cars? I have seen it done on custom built resto mods. And there is an outfit in Phx that has kits and does it in gen one Camaros (Fesler-but they have no plans for a Dart. Something about molds).

I have seen these before many years (have been out of the car game for years). Guessing not OEM. its on my 66 Dart 273.

I am going to hand sand my car to bare metal. Very solid car and no panel work and rust through issues. I do not want to put the metal through the sandblast process and have the time to do it by hand. Since I want to protect the bare metal asap and will only work a panel at the time, is it...

I ran searches in this section and found nothing. Trying remove rear window trim. Which double trimmed. It has never been removed and there seems to be and adhesive that holds it on. Removed the bottom section which is a slip joint. Removed to quarter panel ridge which slips into the outer...

I am hoping someone has a picture of how the spark plug wire were separated and routed from the factory and where to locate those pieces. I have searched over the web. Lots of stuff for big blocks… i have the valve covers with the spot welded tabs. Thank you.

Need grill for my ‘66 Dart GT. thanks

Picked this up yesterday. Started more detailed inspection today. Be sure and tell me what is not factory correct. I plan to restore original with just a couple “drive ability” changes that can swapped back. One is front disc brakes (not sure about power yet) and considering power steering...

Finally acquired a project after lurking on web at old Mopars. Will be here with lots of questions…. 1966 Dart GT solid CA car with original interior and radio. Engine rebuild in 2015 and one lacquer repaint years ago. Console automatic car…and drives! Will post some pics in the right section...

Started my search for a retirement project and interested in a 67-69 Dart. Depending on the model and original equipment, it will decide my course of a restoration or restoration mod. I also really like some the Belvederes and Satellites....will see but wanted to lurk around here and learn...