Search results for query: *

I am selling this dah pad , it is metal frame and newly done , but along rear side there is depressions , unsure what was the cause , it still looks good , perhaps not for a show car , as stated not perfect , and don't want to mislead anyone that it is but it is newly done , picked it up last...

Thinking of buying new glass for my 72 under restoration since all glass is out, the old shows age, unsure how good the side glass will clean , some faint scratches ,,but have already bought new windshield tinted at top,,my question would you go with the original clear or a green tint or a grey...

These have been sitting in my shop for quite some time , still in fair shape and should polish up good , all the bolts are there to install , one of them has 2 of the fake hex head plugs missing but all others there , $100 + shipping

I think this one fits 70 to 71 a-body small block exhaust shield . 318 340 but make sure its what you want , been cleaned and ceramic paint applied $45 + shipping

The first set are black and fair shape , and style that snaps to rear view mirror mount ,,the other set came out off my 72 and are green fair shape , one side of each looks a little brighter green than the other from over the years ,,all of these I consider driver quality , need better cleaning...

What is everyone using for a spray adhesive for seat foam, I plan on starting my upholstery soon and have new foam from legendary ,

Working clutch switch , $125 , I repaired the wire as when whoever removed the clutch pedals , cut the wire to the switch ,so I had bought a new wire for repair but used heatsink with solder and checked resistance is good and works properly , I had a NOS for my project and do not need this one

I am looking for the inserts above the wiper an headlight switch on the dash bezel , I purchased a restored bezel from a 73 before realizing my 72 bezel were not removable as seen in first picture , the 73 has removable indicators from the back , an open hole above the switchs

Does anyone have the small pieces lower in picture that cover the lower hinge area ?

Looking for duster fan shroud for 1972 , anyone have a good decent one before I buy a new one

Looking for one of these ,,saw a few on ebay but shipping is issue with them , the other ships freight , not to mention a high price wasn't helping

This choke came off a 73 340 4bl but should fit many years $50 + shipping

doubled belt crank pulley I believe off a 1973 or 74 dart 340 $30 + shipping

18" 7 Blade fan in good shape , will need clean and repainted $75 + shipping

$20 free shipping

$30 + shipping

new price $40 ,,i think for the lower 48 states I can ship cheap say $5

I bought this last may but not going to use it now , $100 + shipping

Have an a/c rv2 compressor with bracket and pulleys for a 60's era setup I believe , was told for a 68 model ,the pulley an tensioner turn freely but I would replace bearings while there out as there old, the bearings are just pressed in it appears as I took apart to clean an paint ...

compressor turns freely , not locked up , when removed did have some oil in it , just wiped off dirt and cleaned an shot some paint on the brackets , unsure if it works as its been sitting awhile , rebuild is recommended , has coil and pulley also unsure of condition but turns freely , bracket...

Whats the correct size water pump pulley , double or single groove , diameter ? , I will be installing factory ac setup , I have a single groove pulley for a 340 without ac , but unsure if it works with ac

Need front set of seat belts for bucket seats , car is a 72 but don't care about date code as long as there the correct ones for bucket seats

I bought a new engine harness from Yearone , but the old one is different , now I can figure out were the wires run , but my old harness has an extra plug , that I am just unsure were it plugs in at ? I can trace down to add to the new harness easy enough but am I missing something as to were...

I am looking to run something like this setup 215/65 front and 255/60 rear , Will the rear size fit ? Would 3 3/4 or 4.5 back spacing work ? 72 Duster with a large 11" rotors front , 8 3/4 rear installed ,,looking at Torq thrust polished or the Torq thrust D Black or maybe good ole Cragar's...

Bought this fuel pump and unsure of fitting needed for the line side to carb, I know its 1/4 inch NPT threads , so is there a fitting I can source to fit a factory flared line ? Or a fitting to convert to rubber fuel line ? I searched some but not positive I am looking for the right fitting yet...

Anyone have trouble installing these u joints ? They are a good 1/8" or more longer with caps on or off , and do not fit very well and do not go in between the yokes with out a fight , and stick out a bit when installed,,the keepers go in as they should but the original 7260 were small length an...

Got some emblems for the scoops but they don't use a speed nut , they have the plastic inserts , I can probably figure it out but does anyone know the drill bit size off top there head ?

Have 3 different canisters , all mopar , the 1st one say $50 ,, the 2nd $75 , the 3rd $100 this one was has charcoal still , one of the others I think the 1st pictures needs new charcoal added as its missing the other 2 still have charcole but need are original

I have 2 sets of these braces , believe its for auto tranny's only , unsure of value $40 for one set perhaps plus shipping

$225 plus shipping , The upper a-arms are from Classic industries Part # MN6001 , they are new but have been laying in my shop for 2 years or more and have shelf wear , the dust boots are there but cannot find the packages with nuts an carter keys , they are for 1963 to 74 a-bodys , you can...