Search results for query: *

Painted inside the doors (4), but am missing three wire clips for the door panels. Anyone have them?

I need a blue, front passenger door arm rest / door close pull for a 1965 Dart, 4 door. Mine broke. Thanks.

Looking for u bolts and shock mounting plates for a 8 1/4" rear end.

Took the fuel tank out to paint the bottom of the car, but heard hard objects sloshing around. Looks like rust inside, and lots of buildup. Seen new tanks advertised online for about $200, so I am thing of purchasing rather than trying to unsuccessfully clean the tank. Anyone bought one of these...

What parts would I need if I wanted to replace my 1965 273 V8 engine with a 1975 slant 6 engine? The slanty has an auto behind it, while the 273 has a 3 speed on the tree, which I would like to retain. I think it's an A-745 gearbox. Would the Slanty bell housing bolt to the A-745 gear box? If...

Anyone know of a good restoration / body shop in the Ft. Lauderdale / Miami / southern Palm Beach area, that won't charge an arm and a leg to weld in front floor panels? Maybe even repaint the car? Most of the shops I have come across specializes in changing body panels on newer cars only.

I have been searching, but couldn't find how to remove the trim that goes around half of each headlight and the bottom of the grill on a 1965 Dart. Is the trim pushed on from the front over clips, or are they screws / nuts in the back? The trim is in 3 pieces; one for the right, one for the...

I was practicing the soon to be lost art of reading, with the book, "How to Rebuild a Mopar Small Block". The author said that the connecting rods would need to be heated and then a special press used to press the pin out from the rod and piston. Is that true? Prior to reading, I was planning...

Would like to sell my Dart 270 project. 273 V8, three on the tree, factory tinted glass, A/C, new tires, 7 1/4" diff with 2.9:1 ratio or thereabouts, 4 wheel drums, manual steering. Well that's how I got it in Jan 2021, but since that time I have pulled it a part. Engine is at the machine shop...

I am looking into having my 273 bored 30 over (.030 I think). What's the best source for new pistons and matching rings? Cam and bearings also? Thanks

I am in the process of slowly changing my 1965 more-doors dart 270 from a 3 speed manual to a 4 speed 833. Last week I dropped of the dismantled 273 parts at the machine shop to be measured to determine a course of action. My car's odometer says 32K miles, the machine shop owner says the...

Neighbour has a 67 Imperial he is scrapping. Any parts from that car workable in a Dart? Narrowed rear axle and drive shaft? 440 cu in V8? Adjustable / telescopic steering column? Front brakes? My car is currently 273, with a manual gearbox which I would like to retain.

Took the exhaust manifold off, and would love to change the bolts; the threaded shafts are skinny, so would love to avoid breaking in the head in the future. Any sources for these bolts? Specs of the bolts? Also, the OEM exhaust manifold gaskets seem to have spark plug heat shields attached...

What's the best source for a rubber 833 gearbox mount, similar to the OEM? I looked at Brewers and Passon, but saw only polyurethane. To minimize NVH, I have always preferred rubber. PS - the mount has two holes on the gearbox (upper) side for bolts to pass through, and two studs (pointing...

On my 1965 Dart 273, the handbrake cable is below (closer to the ground) the exhaust pipe, but is rubbing on it. Is that the correct routing, or should the exhaust pipe be closer to the ground? From right to left in the pic is the floorboard, driveshaft, exhaust pipe (silver), and the handbrake...

What is the easiest / recommended way to remove the 273 V8 and manual gearbox from my 1965 Dart? So far I have removed the carb (got it rebuilt by Woodruff), radiator, fan, battery mount, and alternator. The engine looks too wide to go down past the frame rails with the exhaust manifolds on...

Do cars with the 4 speed manual gearbox hump use the same "molded" carpet as an automatic or 3 speed manual car? I searched the archive but didn't see a clear answer. Thanks.

Where can I buy, what looks to me from the pictures I have seen, "o" ring grommets that hold the spark plug wires to the valve cover brackets? My 7mm spark plug wires are all tied together with zip ties, so I need to change that PO arrangement. Any recommendations for spark plugs and wires...

Last night I added 5 gallons of ethanol-free petrol to the gas tank, because the gauge in the car read about "1/4" tank the previous weekend (I am not sure f that was accurate). Today when I went to start the car, it would not start by turning the key only (that's how I normally start it). After...

Looking for a four speed manual transmission tunnel for a 1965 Dart.

Bought this A833OD today with the intent of using it to replace the 3 speed manual in my 1965 Dart 273. Need help identifying which vehicle it may have come from, and also looking for a BH if anyone has one for sale. I did some rough measurements and got the following: tail shaft = 17.5"...

Good night all. I recently purchased a 1965 Dart, 4 door sedan, 273 cu in, three on the tree. White exterior, blue interior. It's still on its way to me, so I will post some pics when I get it. Looking forward to all your help and advice, as I have a few things planned.