Search results for query: *

Beautiful stuff. Makes sense, I'll give that a shot. I appreciate the reply!

Hello good folks. Maybe someone can help. I'd like to remove these studs from their clips so that I can remove the stack of washers and then realign the fender. How do you remove these studs from their clips? Here's a couple pics from my car and a pic from another thread showing the stud and...

Any thoughts on this topic?

Hello Folks, I'm slowly reassembling the 67, 4-Door, Valiant Signet after bodywork and paint. It's been a long strange trip! I did a search and I saw a post dealing with this from 2013, but thought I'd be remiss and irresponsible if I didn't mention this (!), and perhaps it might be a helpful...

Hunting and rooted for opinions on where to use windshield gasket sealer on the bottom surface of my 67 Valiant. I have the drain holes and bend up tabs on that bottom surface where the gasket mounts. Sounds similar to your car. Did you use sealer anywhere on the fence-less locations on that...

Greetings! Thanks for the good pics and commentary regrading the 'Drain Holes'. Very helpful. I'm pulling the original weatherstripping (gasket) and windshield back into my finally painted 67 Valiant. I'm planning on using buthyl compound in gasket, at the pinch-weld locations (top, sides and 6...

Thanks for the good input. Yeah it might be a good question for a new thread. I might look at it again and then reach out if it's still illusive. Thanks again for the message.

Thanks for the response. Much appreciated. I should have been more specific. I'm wondering about the 'cardboard' package-tray/shelf itself. My original is in pretty good condition and I feel I'd be sacrilege to paint it. I was wondering what folks have used to clean/preserve/restore the outer...

Thanks for the tip. I'm using the original gaskets, but it might be good to do this since the rubbers have been off the car for about 2 yrs. Thanks for the information!

Thanks for the good information. Much appreciated. Yeah the 67 is an odd ball. My body man was careful enough to save the original front and rear rubber gaskets and I have a cluster of NOS locking strips that I've collected over the years, so I plan to stick with the oddball 67 method. For the...

Hello. I know this is an old post, but was wondering about the leaking around the BOF. I'm currently going to put glass, gasket and locking strip in on my 67 Signet. Did your method (with all those pics) still require additional sealing, due to leaks? Wondering the best method for front and rear...

Beautiful photo and commentary documentation above! The car, and it's components, look great. Question for you, since you seem like a detail-man. I'm reassembling a 67 Signet, in Ireland. I'm wondering if you did any cleaning/restoring of the Package Tray? I'm pondering what to do with mine. Any...

Update. Figured it out. Time takes tme!

Does anyone have a non-destructive trick for removing a headliner rod / bow out of this piece of hardware? I thought it would 'flex' out, but not getting enough movement. I want to remove just the last rear bow so that I can more easily repair a tear in the headliner, on the rear pillar. Any...

Hello good folks. Wondering if anyone has an opinion on this. I have 3 original Finish Panel Clips for my 67 Signet but I need 6 in total, so I've begun making some to match the originals. The question concerns the 'spring steel' type of feature I've circled in blue. I'm guessing that this is...

Happy Saturday! Before I start to fabricate, I thought I'd ask you good folks. I need, ideally, 4 finish panel clips for my 67 Signet. They're approx 4" x 1". See photo below. If anyone has any under a lazyboy chair, in a junk drawer or in a bank's safety deposit box, I'd be interested! Thanks.

Beautiful. So a smaller head nut is used on just the 2 end clips?

Thanks for pointing out the obvious, that I obviously couldn't see! I was thinking about looking for a person with a freakishly thin arm!! I guess in regards to dia of hole I should allow for a reasonable tolerance to allow easy alignment. Any recommendations? I really appreciate your answer...

Happy Thursday folks! Question regarding the mounting of a Finish Panel onto a 67 Valiant Signet. From the parts book it appears that 6pcs of the clips below are to be used. I have 3pcs and plan on fabricating the other 3. My deck lid is from a non-Signet car so I don't have the holes. Below is...

Ok. Thanks for that. I believe I have 4 of these clips. Definitely won't throw them away. That would be sacrilege for a guy like me! I'll investigate the headliner area tomorrow. Thanks for the help.

Thanks for the photo. The headline is currently intact, but all glass is out. Is that photo of the inside of the roof?

Thanks. No the headliner is not removed, but the package tray and all glass has been removed.

Great stuff. Thanks for the confirmation!

Beautiful stuff. I can see the exposed button in my "minds-eye", now! Thanks for that. Luckily I have both! Roof rail clip. I'll have to look at the car tomorrow and see how these work/where they go.

Thanks for the guidance. The door panel clips that hold the interior panel to the door looks like this clip below. Does this one go somewhere else? It's on a 67 Val Signet. Thanks for your input.

Happy Monday! I had someone do some welding work and these items were left in a box. I think the brass-looking piece might have something to do with the carpet, but not sure. The other clip is all metal and the button is about 5/8" in diameter. Any thoughts of where these items go?

Good insight. Makes sense. When I saw the 'washer mark indents', things began to look suspicious!

Thanks LS. Helpful info. Might be the phenonium that MoparOfficial states below. The driver side taking more abuse than the passenger's side.

If he just had someone to talk to, things could have been different! Thanks for your input.