Search results for query: *

I agree. I was pleasantly surprised. It spent most of its life in Florida and moved up to NC for a little while so survived with minimal rust. Although, I am finding more Bondo that I would prefer. Someone must have owned stock!

I bought a 70 roadrunner 8-3/4 off B-body only forum and here is me moving the perches and restoring it for install. I pressed in new studs (got rid of reverse thread) on both sides and did a total brake rebuild. The chunk is a 741 open with 2.9 gears, so that will need to be upgraded one...

Its been a long time since my last update, but I have been driving and working on the car. Took it on the Hot Rod Power tour in 2023 and it overheated due to stuck thermostadt and old water pump, but have been doing a lot. Here is the build sheet I found under the seat. Pretty basic Then I...

I am planning on attending this year. I went last year and did not see too many A-bodies. Hope that changes. Here is Day one line up to tour flashback... (I'm driving the leaning tower of power). Don't think I am theft target LOL!! RGAZ

I'll take it when/if you find it. Yeah I will probably make a bracket to hold it away from the crank pulley. I'll take some pictures as I work on it and note anything special. I ordered it today and it should be here by Friday, so if I get to it this weekend I'll reply back here soon. I...

You guys are the best! I assumed someone found a way and I think I can make this work. Thanks! RGAZ

I have an extra radiator that has bottom inlet on drivers side. Want to use it with the 73 Duster stock slant 6. Top rad hose is no problem, anyone figured the best option for routing the bottom inlet over? I am sure I can figure something out, but wanted to check the brain-trust first. RGAZ

A driveshaft shop can shorten it easily. They aren't near you but I use these guys. Super old school. https://carolinadriveline.com/ At least go to their site and use their forms to make proper measurements. Their forms are very good. BTW - I am doing the exact same thing to my 73 duster...

Not to be that way, but I would rather deal with a member of the forum as the ebay parts I bought before their definition of "working" is not usually accurate. I would rather have someone here who can help me out and would understand my need. Unless that is a member on ebay, but i cannot tell...

Not looking for a restoration quality, but I need one that works better than what I got. Odo mileage does not matter and I just need the speedo itself (not the whole instrument cluster). Looking for it shipped to South Carolina or within driving from Upstate SC. 29620. In case you didn't...

I was considering using them as well as my Speedo is done for and a "might work" Ebay speedo is almost as much as these. If you do go this route, I could probably use your speedo since you will need to reuse the Bezel for those as long as its working. Lets see what others suggest. RGAZ

Rockauto 5% 254730116220073793 Expires Feb 2, 2024. Enjoy! RGAZ

..and I am going to see what it looks like on my hood. Spaced further apart and possible back a bit more. I want to see what that looks like. Stay tuned. (I have to find some reasonably priced and not true resto quality) RGAZ

Awesome! Thanks for the locations. Just for fun I used some Vinyl peel-off black paint to get a feel for how it looks. Keep in mind that this is just a temporary trial for general look before I paint it in (the pinstripes on the inside peeled off easily). I think I like it, but it needs the...

I'll give it another shot, but when I loosened them more, the fluid came squirting out very quickly and made a total mess. Would you happen to know if I should tap it towards the firewall or towards the grille to change the wheels from turning right?

I believe so. I mean it moves so very little that its hard to tell, but I kept tapping away at it and it doesn't move or change anymore. Next step?

I am not centering the wheel. What I am trying to solve is when I start the car the wheel turns to the right by itself. Before adjustment it went all the way to the right lock (pretty quick) and pushed on the lock constantly. Now after adjustment it turns slowly right only a little.

Thanks for this guys. I conducted this last weekend and while it improved the center, its still slightly off and to the right. I loosened and tapped and it appeared to not move any further. I loosened a little more and that was a mistake. It sprayed fluid out from under the valve, so I...

Any chance you could measure and post pictures of the scoop locations? For posterity? RGAZ

It does seem odd. I discovered they are the same as the 69 cuda scoop. Aftermarket has them as non-functional. Only on 73-74 Duster Twister and pretty rare. Most people say they look wrong. Some old posts claim they were functional but from what I see its only if the owner made them that...

Guys, I stumbled across this decal and hood pinstripe kit at Classic (Ma1180). https://www.classicindustries.com/product/1973/plymouth/duster/parts/ma1180.html And in the picture it appears there are two scoops within the decal. Their position seems odd. Can anyone give me details on these...

So to confirm: Jack car up. Start car. Loosen two star-head bolts in pictures. Tap or slide assembly front to back? Is there really that much play there? I don't think I loosened those bolts, but I will give it a shot. RGAZ

I did get the foam up issue too. My steering box does not look like the one in the picture. Maybe I am missing something, but I will get a picture of it tonight and post it to confirm the bolts you are referring to. Thanks for the help, I felt like I was just going in circles! (pun intended)...

From the forum search I found the following: Raise front of vehicle with engine off. Turn wheel all the way left. (engine off) Top off pump. Slowly turn wheel stop to stop about 20-40 times. (engine off) Check fluid level. (engine off) Done. Start engine. So I have now conducted this procedure...

I think I will hit my local Pick a part yard and see if I can get one in good shape. All the other sites want double the price when they include shipping.

I just got a refund saying sold out again. :(

The company I work for has done ecoat for the electrical industry for decades and not all ecoat's are equal. The substate prep will determine if its good or not and you cannot see that or trust it was done well. I would sand off and prep from bare metal for best results unless its used in...

You guys hit them all, I wanted to add a few more: Make sure your MIG tip matches the wire and is new (enough) and tight. Airflow around the piece can ruin the weld. Angle, speed, practice etc. I find setting can really make a difference. I have a Millermatic 110 and it does everything I...

My method: I use a 3" deck screw to plug the hole and then a small square of electrical tape. Next use, pull off tape and pull out screw with pliers (don't turn). Usually works. RGAZ

Changed the fluid, cleaned and painted the cover.