Search results for query: *

something doesn't seem right to me. I have a magnum motor, stock compression, Eddie heads, RPM intake, 1.6 rockers, small cam .482/.496 duration 214/220 with a lsa 112. The cam is ground for 1.6 rockers. Timing is at 14 degrees at idle, i am idling around 1000 rpms, carb is a csu (holley based...

I bought these and was going to go the route of an LA motor but then came across a magnum motor. I would like to get 250 for them plus pay pal fees and shipping. They will be shipped from 48328. From Hughes website "These are a special set of lifters that we helped to design which DO NOT...

I have a set of 273 adjustable rockers for sale. I bought these a couple years ago and decided to go a different route. I would like to get $100 for them plus pay pal fees and shipping. Shipping will be from 48328. -edited to show partial of the shaft.

Have a set of MT valve covers that have been sitting in the garage and I am not going to use. I would like to get 75 dollars for them plus pay pal fees and shipping. Shipping is from 48328.

Come spring time I will be tuning my fitech unit..to messy around here right now. after that is tuned in to where I like it I am adding a supercharger. Engine is a pretty stock Magnum 5.9 with just headers, small cam intake. I was wondering those that have put a procharger or paxton on their...

I am getting ready to install a 360 with 904 trans attached to the motor in my dart sport. Has anyone installed the motor from the top with the headers on or should I lay them in the engine compartment and install them afterwards. The car has Power steering and the column is already in. The...

I have a couple items that I am going to part with a set of J heads with 2.02 Intake valves. do not know much about these heads got them a couple years ago from a guy and they have been sitting around collect dust. Like to get $200.00 for them. a set of 273 adjustable rockers, got these from...

I have 2 different sets of heads right now in the garage that I want to put on the dart. Set 1 x heads with 273 adjustable rockers, New Eddy cam and lifters, springs Set 2 eq cylinder heads magnum style drilled for LA engine. 1.7 rockers (if I go this route I will check for PTV clearance...

does anyone know where you can find the large male pins to go in the ignition column connectors. The white connector I believe the pins are a .125 bullet style pin. I looked a molex's website but could not find them. thank you

dropped my car off Friday to Ididit so they could final fit their new steering column to it and write the installation manual. They are going to start offering Abody Steering columns.:cheers::cheers::burnout:

I am thinking of adding a tilt wheel steering column to my dart. For those of you that have done it what all was involved. I know you have to purchase the steering column and drop adapter, you need to purchase a new steering wheel and adapter. Is there any other parts that you need to...

Started retiring the dart today with the painless molar kit. Only got as far as the front lights before I had to stop. So far it does not seem that bad I have the destructions and the wiring book for the dart. Anything I should worry about? I did some searching already and sounds like normal...

I recently changed over to all autometer gauges on my dash. The car started once then died and will not start. I have fuel and spark on the engine. The one thing I did not do was connect to the 12v and the ground on the original wiring group. I pulled the power from the fuse panel instead...

My dart is a 76 sport and from what I can tell it has a shunt style amp gauge in it. There was only small wires (18 gauge or so) running to the connector that the gauge was connected to..there were no 10 gauge wires. Anyways I am in the process of replacing the gauges with autometer gauges...

I just picked up a pair today at the mopar nats. My question is they did not identify which one was right and which one was left. The springs have a part number 1981 and 1982 on them. The website does not say which one is right and left...any way to tell? thank you

I know mopar small blocks like around 32 to 35 degrees of total timing. Is that initial plus mechanical or Initial+ mechanical + vacuum advance. right now my engine is set at 8 degrees initial, 24 with the mechanical in full, and around 44 with the vacuum advance connected. It sounds like its...

On my dart the driverside turn signals work great, the passanger sides seem to go very slow. I have replaced the timer and checked the grounds and they all seem to be good. What else could it be?

is anyone repoping original overflow bottles for the 76 dart sports? I looked at dantes, yearone, bea and have not seen any...or am I stuck with going to an aftermarket non original looking one. thank you in advance

I have a failry stock 360 motor with a ld48 intake, headers and ignition system on it, I just recently purchased a eddie cam the bigger one of the two. I know it wont work with stock springs so would I be better off waiting until I can afford eddie heads to go with the cam or change out the...

if anyone has little kids that likes toy trains, they are welcome to stop by my parents house on sunday from 10 am - 4pm. http://www.candgnews.com/Homepage-Articles/2010/07-14-10/Bloomfield-Dunn-railway.asp

just got done wetsanding the dart, broke through in a couple spots that I am going to have to fix tomorrow but it came out nice. Not to bad for my first real paint job.

any tips or tricks for removing the windshield from the car. I have a 76 dart sport and I need to change the gasket. Do I just cut the old one out or is there a locking strip some where? Thanks Rob

got the engine bay painted, its still wet in some of these pictures. Kind of did the chevy thing, its hotrod flat black paint. Car is going to end up corporate blue before its all done. I know some of you might not like the idea of a black engine bay but withe the blue car, I did not want the...

I looked at the back of my gauge cluster and I can not see where the wires come into the amp meter. I have the printed circuit board on the back of gauges and do not see any wires going to the amp meter. Is it in the round plug connector that plugs into the back of the gauge panel? If so...

anyone know the paint code for petty blue? I was at the paint store yesterday and they were trying to tell me it was b3 but that does not sound right. I am going to be repainting the dart this winter and want to do it in petty blue. Also has anyone used the tcpglobal.com paint. I think they...

Wanted 360 stock oil pan...must not leak. My chrome one leaks and I would like a decent condition stock one. Will consider reasonably priced unit. email me with what you have and pictures preferable. black00rt@yahoo.com Thanks Rob

where can I find the spring that goes on the kick down lever and goes to the bell housing. I have checked my parts stores and have not been able to find a listing for one. Is this a dealership item, I find that hard to believe.

what size are the drums? My axle assembly that I bought did not have them on and I need to purchase a new set. Also can you find these at your local parts store or do I have to get them online someplace? Thanks they are 11" backing plates

Just scored a complete 904 trans with 10k on it since rebuilt for 40 bucks. Guy pulled it out to go to a 518. Now I have a couple questions, I am going to replace my /6 with a small block, what shift kit is everyone using? also can I reuse my kickdown cable or do I have to buy a new one? I...

I just changed the brakes on my dart. I did drums all the way around. I changed the master cylinder and bleed all the lines. I have full pressure to the lines yet my light on the dash will not go out. I checked the connection at the prop valve and its on and fine. Yet still nothing. I have...