Search results for query: *

  1. cudajoedart

    Chryslers At Carlisle

    Hi all anyone going to Carlisle in July, I will be vending there in spots N30 N 31 have A-Body parts stop by and talk MoPar hope to see you there Joe
  2. cudajoedart

    [FOR SALE] 1966 Dodge Dart (project hood)

    Hi All I have for sale a rust free hood from my 66 Dart, it had a tunnel ram scoop on it, I have replaced it with another hood that has a Challenger bulge, this would be a good hood for someone looking to put some type of scoop on it, without having to cut up a good stock hood, I can not...
  3. cudajoedart

    [WANTED] 1965/1966 Dart, Valiant, Barracuda A/C heater control assembly for factory A/C

    Looking for A/C heater control for factory A/C I am installing in my 1966 Barracuda
  4. cudajoedart

    [SOLD] 1985 Dodge Ramcharger Royal SE

    I am selling my 1985 Ramcharger after 27 years of ownership, the body was redone and painted 9 yrs ago the engine was rebuilt about 15,000 miles agowe made the trek to Carlisle in July. runs good the plow was only used for personal use this would be a local pickup only Truck has: Cold a/c...
  5. cudajoedart

    [WANTED] Engine pulley

    Looking for the lower crank pulley (3 groove) and the a/c compressor bracket with idler pulley for 65/66 a-body small block 273 do not need compressor Thanks
  6. cudajoedart

    Chryslers At Carlisle

    Hope to see & meet some of you there look for the 66 yellow dart convertible with the Cuda hood Joe
  7. cudajoedart

    [WANTED] A/C Compressor mounting bracket

    Hi all I am looking for a factory a/c compressor mounting bracket with the idler pulley for my 1966 barracuda with a 273 any help will be appreciated Thanks Joe
  8. cudajoedart

    [WANTED] 1966 barracuda engine pulleys

    Hi I am looking for lower dual crank pulley for power steering also need a/c bracket with idler pulley adding power steering and a/c to my cuda any help is appreciated Joe
  9. cudajoedart

    [SOLD] mopar 833 4 speed transmission (overdrive)

    For sale New Process (833) 4speed (overdrive), not rebuilt disassembled, clean and inspected only saw slight wear on the 1-2 shift fork, new shift selector o-rings, tail seal and reverse light switch finished in cast gray paint has tail shaft with two shifter locations, Hurst shifter included...
  10. cudajoedart

    Register For Carlisle Black Friday Discount

    Hey MoPar fanatics I just registered for the Carlisle MoPar Nats. saved a few bucks do it now Joe
  11. cudajoedart

    [WANTED] 1966 Valiant/Barracuda fender

    Looking for a good left front fender could possibly work trade if I have something you need Joe
  12. cudajoedart

    My 66 Cuda

    Hey Guys Here is what I am working on,I bought this car in 1973 from the original owner I drove it until 1982 then it sat for 38 years finally getting to it, it is an original 273, 4 speed, disc brake car,8.75, half vinyl top, rear I am putting in factory a/c here are some photos...
  13. cudajoedart

    [FOR SALE] Chrysler Air Temp under dash A/C unit

    Chrysler Air Temp Under Dash Unit For 1963/1964 Dart/Valiant Asking $300.00
  14. cudajoedart

    New to the site

    Hi all I am new to the site and have been an avid MoPar fan for 54 years in my stable I have a 1966 Dart 270 owned since 1967,1966 Dart 270 convertible,1966 Barracuda (in process of being restored),1985 Ramcharger and a 2006 Chrysler 300
Back
Top