Search results for query: *

Looking for the 4 bolts that hold the rear bumper brackets onto the frame. thing the have an 'H' on them. have a set? thanks

perfect, thanks for the info everyone!

Hey guys, Anyone know what the color the the lower radiator support was from the factory? See some painted the color of car and some black. thanks

thanks guys!

Hi Guys, Looking for a little info on how the quarters were undercoated inside trunk? Was it just vertical surface from front to back? How far forward? Any help appreciated. Thanks

hey guys, For the record, its not a horrible noise. Its just obvious when I let the clutch out. I am running 80w 90 valvoline. was going to go for the valvoline 75-140 GL4? Or go with what you guys suggested to start.

sorry for being that guys who responds many months later. I appreciate the help everyone. I suspect its the oil. Have not had a chance to change it out to something heavier. I did adjust the throw out bearing and that was not it. After winter I am going to try a heavier oil (since its rally...

Guys, thats a big help, thank you. Also I did the pilot and throw out bearing too, so basically I shouldn't hear a difference in clutch in clutch out in terms of noise? and I didnt think to check my throw out adjustment but I can always hear the noise intermittent so that's the first thing I...

Guys, looking for little help. Have A833 4 speed in my 69 dart. I replaced the input bearing when installing trans because it was obviously noisy. The trans is still a little noise when I let the clutch out at idle. Is this normal for the A833? also, anyone know will a '75 OD 4 speed trans...

Max, really I just need spindle bolts to lower ball joint but if its easier to send spindles with drums, I will seperate them out. sent you a PM. thanks!

Any chance you would ship spindles with drums, I really just looking for spindle to backing plate hardware.

Hey, how did you do with the oem style bolts? any luck. I notice they do make contact when you lock the wheel out, I will probably end up with a generic grade 8, but would prefer the dome head.

yeah, suppose your right. thanks guys.

Ok will get a picture, I think I am describing poorly. Basically the lower ball joint bolts. Anyone replace them? any remanufactures out there?

Guys, looking for a little help. restored my 69 dart some time ago and noticed the head of the lower rear spindle to ball joint not is not totally against the lower ball joint, can anyone check theirs and tele if this is normal? also, has anyone changed these? and what did you guys use if so...

Hi, looking for a front left sbp - with eft handed threads. 10" do yo have anything (mine pitted)? thanks

I have the following dart glass I am looking to get rid of; clear side door glass still new in box from PG auto glass - $15 each original tinted side door glass from a 68 dart - $25 each tinted vent window glass 68 (I think) - $20 each original clear rear quarter glass fro 67 only...

Hi, yes, councours. these are makings on some of the bolt heads and I am just finishing a restoration on a 340 dart. I figured I might as well get the right bolts oin the right place thanks

guys looking for a little help on following bolt id and where they go; 1. the vibration damener to pulley, are the the 'E' head bolts? 2. the engine ground to block are they the "I/C/S" bolts?? 3. Is there a washer on the bolts that connect the pulley to water pump? 4. what is on the head of...

guys looking for a little help on following bolt id and where they go; 1. the vibration damener to pulley, are the the 'E' head bolts? 2. the engine ground to block are they the "I/C/S" bolts?? 3. Is there a washer on the bolts that connect the pulley to water pump? 4. what is on the...

bucket seat bezels

bob, measured offset is 7/8" to be exact. the front bracket bolt pattern has bolts spread 1 1/2" apart on top and 1 3/4" on bottom to clarify things let me know thanks

Guys, I have the following I am looking to sell 1968 hp 383 carb core only- number e94682sa $25 1969 383 hp core only - a84401s $25 fuel rail for 6 pack $20 (pls check pic, I might need correcting here, and it might be incomplete) hood pin studs. - $20 they are driver quality nice slant...

selling a set of driver quality bench seat bezels, looking for $25 for all five plus 4 nice screws. also looking for $20 for the "dart" badges. they are nice froma what I can see but have a coat of white paint on them that needs to be stripped. location philladelphia area. thanks

Guys, I am looking to sel a set of offset shackles and the front leafspring mounting bracket. they came off my dart, but were not correct for it. Any comments on what they are correct for would be appreciated. looking to get $30 for everything (one main eye blot slightly stripped). location...

lets see if I did this right;

I can get some pictures this weekend, the gears are in good shape, pulled them out of my dart for 3.23s

guys, sold the spring to a local memeber yesterday, being picked up today, thanks for the interest

I'll get some pics up by weds guys

have a set of 4.56 gears in nice shape for a 742 case, looking to get $75 and shipping from Southeast PA also have a set of ss leaf springs from my dart, very low miles with front bolt bushings already in (in good shape too), I only took them out becasue I wanted a smoother ride - looking to...